WFW9600TC00 Whirlpool Washer - Instructions

My son pulled the washer out and found the parts that was leaking. He ordered the parts from your company. they arrived the next day and he re-pared the leaks and all is well.thank you

I removed the old pump and replaced it with the new one. I am the happiest person on earth right now to have my washing machine working at its best again. Thank you so much.

Replaced water pump

Removed top of washer and replaced flow meter.

repair was a cake-walk with the video there to help.Thanx

I followed the instructions and it was surprisingly simple. Glad I didn't call the "handy-man" since it was easy to do it myself as a handy-woman!

I watched video first and it help me a lot to do the repair myself of my washer machine and i save about $ 1,500 dollar. Thanks

Took old one off and put the new one on. Was very easy. Hardest part was disconnecting hose clamps, which was still easy

took front panel off. Pump is right there easy to work on. Used pliers to take 2 hose clamps off. Used star screw driver to take 2 screws off of pump and removed old pump. The Assemblely goes the same way but the drain hose coming off the tube is not very easy to get back on. Hose is flimsey and the stem, on the end of the drain pump isnt long enough to keep hose on while tring to slide hose clamp back on.

Read the instructions provided by PartSelect.....and with a bit of patience I installed all four bolts so the washer's inside agitator was not damaged in shipping. I highly recommend that anyone who is moving/storing or shipping their washer that you find the correct shipping bolts according to your model and make and install them prior to moving your appliance.

Unplug the power first.If you can lean the washer bank and support it with something underneath to make it easier to work on.Removed the 3 bolts at the bottom panel underneath the front door. Pump is right there in front. Unplug the power connection first,you can also remove the wiring that is right in front of the pump so it will be out of the way. remove the pump from it mounting grommets and pull it out a Little so you can get to the hoses at the back of the pump. Using pliers to pull of the hose clamps you can pull off the hoses. Now you can remove the pump out. Do everything in reverse and that's it. I found it to be easier than I thought and took less then 20 mins.

It was a little difficult to put the new Bellow in place on the tub, due to the fact you have to basically push the outside of the Bellow all the way into the tub so you can install the tub clamp. The other difficult part of the task was tightening up the clamp it's self. There really isn't a lot of room to move your hand around in the space you are given to work. But after a few hand cramps and a few things said, that are not needing repeated, I was able to get the clamp tight. Once you have the clamp on the tub, it's basically pretty simple to slide everything else into place. The wire/spring clamp that is used to attach the Bellow to the front of the washer is fairly simple to put into place with a little patience. All in all it was a cheep and easy repair for a due-it-your self repair.

Followed video clip that I found online

Opened lower front panel to access the motor controller. Took a picture of the wiring attached to the front of the controller. Removed two wiring harnesses and one wire with a retainer clip. Removed the faulty controller. Inserted the new controller, replaced the wiring, using the picture to insure correct positioning (although that really wasn't necessary because the wiring clips could probably only be put in the correct places). Replaced the front cover, plugged in the washer and fired it up.

The difficult part was getting the water from the washer without making a huge mess. I used a shop vac loosened the cover on the filter/strainer assembly use the shop vac to suck up the water before spills all over. if the tub is full I dumped my shop vac twice total. 1 Remove pedestal drawer 2 removed lower cover to expose mechanicals and pump assembly 3 vac out the water by using above procedure. 4 rotate hose clamps to a position where you can get the needle vice grip on them/remove hose clamps. 5 lift cover exposing electrical connections on the pump assembly depress tab slide connector out. 6 remove 1 torx head screw securing pump to base of washer. 7 remove pump assembly. 8 Reinstall in reverse of above instruction. I also took the lower tub hose off and washed, bleached along with hot water to. clean it