WFW8410SW02 Whirlpool Washer - Instructions

Used suggestions on list - water to lubricate bellows and an extra hand to secure the bellows. Biggest challenge was seating the bellow that attaches to the rim of the outer tub. After getting the bellow lip seated the rest was fairly easy including the bellow seat that secures to the outer door assembly. Unfortunately, it doesn't appear that the bellow was the problem even though the symptoms - leaking under the door - was the same as noted on the list of problems. Had to order the dispenser-to-tub hose as that looks to be the problem (had to contort to follow the leak all the way up to the hose).

I followed the clear directions. Any hiccups were due to wear of the parts as they were quite old. This included both wire clamps.

Boyfriend followed directions and YouTube and I’m sooooo grateful!! My door shuts easily.. I love my machine and my man with your directives and your parts made my magic happen!!

I never did the repair because Partselect.com shipped the wrong part. Then they charged me a 2nd time to resend the correct part plus the fees for shipping the correct part overnight which I did not get it until 2 days later. Now I shipped both parts back & have to wait for a refund.
I will never order from them again!

Pushed new baffles on tub clips. Pushed baffles towards the back of tub. They have been working great.

Checked for 120 V AC at pump connector. It was present . Pump was hot. Ordered new pump. Changing the pump is a piece of cake. Just tilt machine back and rest on a brick. Remove 3 5/16th screws . Disconnect 2 hoses and 1 plug. Took 10 minutes tops. Back in business.

After further investigation I realized that the original dispenser hose from the soap bin to the inner tip was the cause of the leak. Before this repair, I replaced the bellows. And as part of that replacement process you have to remove the washer dispenser hose from the inner tub so that I could complete the bellows installation. However when I put everything back together the old washer dispenser hose was leaking terribly. This was fixed easily with a new hose and an 1-1 3/4 inch hose clamp. I found an installation video that allows you to come from the top down to replace this hose but for my model of washer and because the drier was stacked on top, I took apart the front of the washer since I learned from a different video how to do this in order to install the bellows. No more leaking at all with the new hose.

This repair is something even the most casual DIY'er could accomplish. What made this even easier for me was the fact that my washer was on a pedestal so accessing the 1/4" screws were extremely easy. There is no need to tilt or lift the washer. Just open the drawer and all three screws are visible. It also made draining the water out of the washer very convenient. The video perfectly describes how to accomplish the repair and allowed me to diagnose the problem by taking off the panel, opening the trap door and allowing the water to drain into a small trashcan until all the water is removed. I could physically see that the impeller was detached from the motor and found the culprit that caused the problem - a small vile of eye drops... From there, ordered the pump, two days later, replaced it with the new and I swear the new pump must be stronger than the original because towels come out near dry after a spin cycle. Very satisfying repair!

Turn water off at the inlet valve of hose you are replacing. Disconnect inlet hose the washer and let water drain out in a bucket. Then remove old hose. Replace new hose to inlet valve then washer . Use pliers to tighten both ends. Turn on water to check leaks at both ends of hose.

Replaced drain hose

This was an easy fix . PartSelect was quick and had all the info I needed to repair my washer. Plus shipping was super fast. Thanks

The removal of the bellows was easy and quick. The instructional video was really good. Only one problem with video. The step of removing the console from washer leaves out that there is a center screw in the center of console. I almost broke the console. It took took a long time in getting bellows on interior area due to tight finger space. Wire gasket fairly easy. The outer gasket after getting door and latch on. Whew! That was a bear. Video looked easy. I finally had to get help to get it on. The reason was that every time I thought I had it, the bellows would roll off will the wire gasket. A screw type as the inner area would make it so much easier. Shipping. Kudos to your company. I was expecting that I would be without washer for a week. I ordered on a Friday and it was here early Monday morning. That was amazing. By the way I did this except the outer wire gasket by myself. I finally had to get "husband" to help with that. Thanks Parts Select! If the need arises that I need another part. You will be my go to company.

Followed the most helpful video.with some system differences. Had quite a bit of fitment challenge with the inner bellow sealing process...finally used dish soap to help 'stretch' the thing on.Works fine now thanks.

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

Had my appliance man do it. It was the first one he had ever done in 20 years of working on Whirlpool. It was quick. The parts I received from you were cheaper than his supplier. Needless to say that made me very happy!