WED6200SW0 Whirlpool Dryer - Instructions

Removed top cover. Removed front cover. Removed Drum. Located the broken belt. Found that there was no tensioner in the unit. Replaced drum rollers. Put in new tensioner. Repaced Drum with belt around it. Installed belt through tensioner and onto drive pully of motor. Supported Drum with wood block. Turned on dryer to insure drum turned without any problems. Removed wood block. Replaced front cover and top cover. Repair compete.

To be short and sweet, the repair was simple once I got the parts I ordered which came really quick. I put them on and it worked fine. Ez to install as well. It only takes half the time to dry, it seems to work better than when it was new. I saved hundreds. The repair man was going to charge $69.99 just to come out to see what the problem was. The parts I needed were under $100 so figured I'd try an do it myself, after reading others repair stories. I did it! I will be a repeat customers if something else breaks down. Thanks Partselect.

unplugged the dryer-- opened the back of dryer--tested the element--found there was a break in the element--ordered a new element--put everything back togethered and it worked. 10 screws held the back wall on--2 screws and 2 wires to disconnect the element---not very difficult!!

To replace the light bulb, I removed the screw and the cover, unscrewed the old bulb, replaced with the new bulb and replaced the cover, securing it with the small screw. It worked appropriately with normal use for a few days and then I noticed the light was not coming on when I opened the door.

I removed the cover and pulled out the bulb to find that the filaments inside are dangling and burned through. I need them replaced, please.

Remove top,front and panels.change thermal fuse and outlet thermistor.

Simply checked the thermostats for conductivity and found that they were working properly. Removed the heating element to check for conductivity and discovered a broken coil. If I had the part ready to go the whole process from taking off the first screw to replacing the element to screwing on the last screw would have taken less than 15 minutes. Very simple repair that I almost paid a service technician an additional amount for something that a novice DYI'er could do.

unplugged the electrical cord, took the back off the drier, unplugged wires from the bad heat unit. took couple of screws out that hed it in place, removed it , installed the new one plugged wires back , put the back on , plugged in electric cord. turned it on and that was all , works great. the part you guys sent was identical to the original . thanks. Ken

first with the dryer unpluged ,i removed the wires from the upper thermal cut off ,then with a nut driver i removed it . replaced it with the new one and reattatched the two wires then the same on the bottom thermal . to replace the spring i removed the two screws pulled out the switch and spring at the same time ,removed the broken spring and replaced it onto the switch then placed it back into the dryer and replaced the screws.! everything worked like it han never been broke! my wife is verry happy!!!

pulled dryer away from wall took screws out of lint screen lift top removed 2 screws one on each side of front at top and removed front panel. pulled belt off drum removed drum rollers tension pulley and while i was at it pulled back cover off of heating element and blower blew everything out with air hose did a total cleaning installed everything in reverse. i was amazed how fast the parts came the dryer was only down 2 days and it runs like new even if it is 20 years old i highly recommend parts slect and i will use them in the future

First cut breaker off, removed wall plug, then removed back panel removed old element installed new one, had a great opportunity too clean lint from blower, and entire unit. Very good job. The video with instructions was awesome.

I highly recommend using a multi-meter to test for continuity on the thermistors and the heating element. It will likely save you a lot of time and you can replace the correct part the first time. I found the high limit thermostat to be open. Also note that if you find the same part open, it is most always caused by another part failure or the dryer vent to be clogged up with lint. I also cleaned out the lint chamber which was in pretty bad shape and likely caused my failure. But, the parts were not expensive and were replaced while I was doing the trouble shooting. The video is excellent and if followed all will turn out ok. This is my third different appliance repair, and the parts are always in stock, the standard shipping was 7 days, and everything you need is provided.

Followed online video very easy and dryer works like new one....

Removed the top, removed lower front cover, removed the front, removed the belt, removed the drum and the back. Removed and replaced roller support shaft and drum roller’s. Completed all Front and rear support for drum. Replaced drum , replaced drum roller belt and replaced back, completed replacement of the top, front.

Purchased new heating element and replaced. This was the number one recommendation for the fix for my problem. I do not have any measurement devices to check any of the parts. This was trial and elimination. The old element was badly burnt. Still no heat. The second recomendation was the thermal fuse. I purchased that and replaced. Still no heat. After reading through some of the repair forums on this site I decided to try one more time and replace the thermal cut off kit. A little harder to do because it required cutting and replacing some wire ends. That was the problem. We now have heat and once again I have a happy wife! I left the new element and the fuse in. The dryer heats much faster than it did.
The repair videos on this site were very helpful. Some of the wire changes on the Thermal Cut-off Kit can be very confusing.

Watched a couple of you tube videos, seemed simple enough. Used multimeter to test thermostats, still good. Took off the heating element, it was visually broken. Called the 800 number, the guy who answered told me how to find the model number of the dryer. He then told me the part number and it matched what I had. Ordered, 2 days later arrived, just plugged it in and reinstalled the back covering, works great!