WED6200SW0 Whirlpool Dryer - Instructions

I removed the broken door catch with a screw driver. I then used a pair of pliers to push the new door catch in place. It was an easy repair and saved me quite a bit of money.

Pulled the dryer out from the wall and laid it on its front on a blanket.Removed the back panel.Disconected the two switches and replaced them with the new ones.Cleaned up dryer replaced back panel and returmed the dryer to its original place and she works just fine.

I changed the belt, tension pully and rollers. Runs like new now. I also took the opportunity to clean it out real good while I had it apart.

Replaced thermal sensors.

First cut breaker off, removed wall plug, then removed back panel removed old element installed new one, had a great opportunity too clean lint from blower, and entire unit. Very good job. The video with instructions was awesome.

We had to pop open the top. Unscrew front of dryer from sides. Disconnecting the wires was a bit more difficult than expected. We had to use a tiny screwdriver to slide into the sides of the white wire connector on each side before pulling apart. Front drum falls when front of dryer is removed. It took two of us to reassemble - one to hold the drum while the other put the front on. Our problem turned out to be one wheel. We replaced both wheels and saved the rest of the parts. Hums along just fine.

I highly recommend using a multi-meter to test for continuity on the thermistors and the heating element. It will likely save you a lot of time and you can replace the correct part the first time. I found the high limit thermostat to be open. Also note that if you find the same part open, it is most always caused by another part failure or the dryer vent to be clogged up with lint. I also cleaned out the lint chamber which was in pretty bad shape and likely caused my failure. But, the parts were not expensive and were replaced while I was doing the trouble shooting. The video is excellent and if followed all will turn out ok. This is my third different appliance repair, and the parts are always in stock, the standard shipping was 7 days, and everything you need is provided.

I attempted to take the back panel off the dryer only to discover all I had to do (after removing 10 or so screws) is remove the lower base plate in the front of the dryer. I also had removed the door which turned out to be unnecessary. After removing a guard in front of the heating element (2 screws) I yanked the the element housing that contained the heating element and then disconnected the 6 wires. Using my first ever, newly bought multi meter for only $9.99 from Radio Shack, I turned the dial to the infinity section and check the element for continuency. I did this by touching the meter's two probes to the element's terminals were the wires connect. The element was fine. Then I checked the two sensors the same way. The sensor furtherest away from the element's terminals didn't have a constant signal so I assumed that that sensor was bad. Well, come to find out, one sensor is open and the other in closed... only when the temp. changes do they operate by opening and closing the current. By this time I had already ordered the part so it was too late. Surprisingly, the part came in 2 days. I ordered it Sunday night and i figured it would be sent out Monday but it was already in the air Monday morning... Great service! I replaced both sensors and the dryer works like it did when I first got it.

Unplugged Dryer.

Removed back panel & dryer hose - About 10 screws

Removed Heating element - two screws

Followed instructions for replacing old thermal cut-off with new model (this was slightly different from original equipment - wiring modification was required) All connections were detailed in the instructions. Jumper wire and new screws included in Thermal Cut-Off kit.

Cleaned lint and dust from inside dryer.

Replaced back panel and dryer hose.

Tested dryer, works like new.

pulled dryer away from wall took screws out of lint screen lift top removed 2 screws one on each side of front at top and removed front panel. pulled belt off drum removed drum rollers tension pulley and while i was at it pulled back cover off of heating element and blower blew everything out with air hose did a total cleaning installed everything in reverse. i was amazed how fast the parts came the dryer was only down 2 days and it runs like new even if it is 20 years old i highly recommend parts slect and i will use them in the future

I opened the top and front of the dryer. 1st I pulled out the drum and cleaned up the lint and mess from the busted support roller. Next it was a matter of looking at the enclosed drawing and instructions. I could not believe it was that easy.

This was soo much easier then I thought!!! Make sure you unplug the dryer FIRST!! I removed the bolts that held the dryer back with the socket wrench. The removed the 2 screws that held the heating element in place. Disconnecting the cords was a little harder but will come off with the pliers. There is that piece of your old heating element that you need to remove to put on the new one that was hard to get off. its being held on by a metal lip and at first I couldnt figure out how to get it off, but then I just kept bending it (the metal lip) until I was able to get the piece off of it. Then just connect the wires onto the same points that your removed them from. Replace screws and back of the dryer and WaLa!!! You've just saved yourself the price of labor for an electrician.... Trust me if I can do this YOU can... My husband thought I was crazy.. I get shocked changing light bulbs but my dryer is drying a load of clothes as we speak!!!

Removed the top, removed lower front cover, removed the front, removed the belt, removed the drum and the back. Removed and replaced roller support shaft and drum roller’s. Completed all Front and rear support for drum. Replaced drum , replaced drum roller belt and replaced back, completed replacement of the top, front.

It went well, I followed the instruction video and referred back to it if any questions or difficulty. The instructor on the video was obviously very experienced and duplicating his actions exactly was very helpful, One thing I noticed that wasn't mentioned was that the thread on the wheel / motor is left handed.

Followed online video very easy and dryer works like new one....