TS518SW Amana Refrigerator - Instructions

I first loosened all screws that are hidden by seal leading edge. I then removed seal. I made sure that I knew which side of seal was to be in contact with refrigerator door frame to provide the seal. I positioned the seal on the door inner panel starting at the top. After I had finished positioning the top I proceeded to position both sides and then the bottom. I tightened the screws only enough to hold the seal in position. After I had the seal in the proper position I tightened the screws that hold the seal in position. I used a hair dryer to heat seal and smooth out the the sealing edge.

Unscrewed the old handles and replaced the new handles with the same screws... that easy! It was the easiest repair that I ever had to do.

Took out three screws, kept the little plastic cover on the bottom screws and the screws--they did not come with the new handle. It took less than 5 minutes to do the whole job and while it was off I got to really clean my frig. Thanks for the quick delivery!!

simpley place the support into slot provided.

1. Turn your water OFF and pull the refrigerator out from the wall so you can access the back.
2. Use pliers to remove tubing clamp.
3. Remove old water fill tube.
4. I used a putty knife to gently pry out the old fill tube from the back of the refrigerator. Once the fill tube pulls out about 1/4 to 1/2", then you can gently pull the remainder of the tube out by hand. Once I removed my "old" fill tube, that is when I saw the "ice plug" that was causing pressure in the water supply line and caused my water line to pop off.
5. Install new fill tube. The end that goes in first needs to go through a small "ring" inside the freezer (this "ring" is not encountered until the fill tube only has about one more inch to be inserted into the back of the refigerator. I could barely see this "ring" if I opened the freezer drawer and stuck my head in as far as I could. I had to gently rotate the new fill tube until it cleared the "ring". You will feel some resistance until it lines up properly.
6. Snugly push in the part that stays on the outside of the refrigerator until it looks like it is sealed.
7. Gently push up the water fill tube where it belongs in the new part and replace the tubing clamp.
8. Turn your water on and make sure there are no leaks (I left my refrigerator out for about an hour).
9. Push your refrigerator back in place.

The Ice maker unit had to be removed and the shaft had to also be removed, which required dis-assembling the motor drive. The thickness of the shaft and the bearing fill cup prevents it from simply pushing it in place. Other than that I have Ice.

I removed all the screws except the top screws. These screws I loosed to make sure the door shelves remained in place. I did not want to remove the refrigerator door. I had read this method on PartSelect. It worked fine. I would recommend a power drill because of the number of screws supporting the door shelves; a power drill really help.

Please note there are only 3 sides of the "new" door gasket that are magnetized. It would have been nice to identify which are the magnetized sides before I did the installation; I guess I should have read the directions before hand.

It was an easy job.

Removed the 2 screws holding the light bulb shield, then the 4 uolding the metal panel. Unplugged the olw door switch and replaced.
reassembled the pieces.

proped up frig, loosened screws, cut pin, installed rooler w/ new pin, rounded pin end, reistalled, lowered frig...everyone happy, thanks again partselect.

First I removed the two screws that held the top of the handle in place. Then popped off the bottom holder. Replaced the broken handle with the new one, replaced the screws and snap on section and now have a nice looking refirigerator with a handle that works.

Referencing the info/schematics you have on your website, I unscrewed/unattached top-front panel (carefully), from behind the panel you have to detach the wires (2) from the switch, pushed "in" the switch to remove, put in new switch and attach wires to test BEFORE remounting panel. Tada!! Thank you PartSelect! You saved me at least $80...would have been at least $100 to have a repair person come to the house!

unscrewed the side rail and rotated it to remove it from the rest of the assembly. Then ran the humidity tape through the new one and screwed it on. put it back in the ref and put the glass back on and the drawers and it was done!

removed the old handles and replace with the new. It was all very simple.

Cut old fill tube into pieces, removed and replaced with new tube. Extremely easy.

Repair went well,took about five to ten minutes to disconnect the power from the fridge removed the defective switch installed the new one ,reconnected the power,,,and Let there be light and there was light!

Very easy to order from parts select. Took seconds to replace.