TS518SW Amana Refrigerator - Instructions

I first removed the screws from the upper 2/3 of door gasket and remove that portion of gasket. Put new gasket in place and re-installed the screws on the top section. Removed the rest of the screws, completed placement of new gasket and re-installed all screws. It is not necessary to remove the door. Piece of cake repair.

The part was delivered in just a few days. We merely had to unscrew the broken handle and screw in the new one. The color matched wonderfully and funcitoned beautifully.

Pop loose the plastic grate at the bottom.

Locate and remove the wheel leveling screw from the front bottom corner.

Remove cotter pin from the pin that mounts the wheel assembly to the refrigerator. Tap out the mounting pin.

Lift out the wheel assembly.

Remove the Roller pin from the wheel assembly. I used a Dremel tool with a cutting disk. A hack saw will also probably work.

Install the new roller pin and wheel into the wheel assembly. Use a hammer or vice to peen over the end of the roller pin.

Reinstall and adjust wheel assembly.

Removed the hinge cover, removed three hinge screws, removed door. Then I used a screwdriver to pry out the hinge bushings, pushed the new ones in and replaced the door. Both Maytag and Lowe's (who held the extended warranty) said that the door was not a repairable item and would have to replace the whole door. Since that would cost more than the value of the fridge, they voided the warranty and returned my cost. Too bad we didn't know about Part Select, we would have held their feet to the fire.

Just replaced the switch, but unfortunately that was not the problem; nor was it the bulb....so I am back to square one.
But Parts Select is a great place to order from. Thank you.

Icecubes came out half-way, and refrooze. I figured out, that the melter does not work (HEATER in the icemaker) Voltage measured 105V no load. Studied the Internet, and folloved an advice: shorted the back wire and the blackwire with white stripes.these go to relay contacts. It seems, that the relay contacts are no good on Infrared receiver boaed. I turn off manually the icemaker, when needed

Had to disassemble ice maker to install part. . .

I hired a jack-of-all-trades friend of mine to do the job. He had just the right tool to take out all the screws so that went smoothly. Slipping the new gasket into place while I held the inner door shelving section in place was a little tricky and the gasket seemed a little off along the bottom and one side of the door frame. We gave it a couple of days to seat itself. Two days later, there was condensation forming inside so my friend returned and took a look. He spotted a couple of places where the gasket magnet was not sealing properly. Out from his pocket, he pulled what looked like a brass jack knife with japanese writing on it and said it was a japanese carving tool. He opened up one of the parts that had a smooth blunt tip on it and slid it down the channel in the gasket from the outside. Voila! The magnet grabbed. He adjusted a couple of screws along the bottom and , after that, there were no more problems. So be sure to have your japanese carving toll ready when you start this job!

The good news is that the part (the wheel was available.) I bought two in the event that the other wheel may break in the future. The bad news is that the housing that holds the wheel was riveted together by the wheel axle. It would have been nice to know that before I bought the part and if the housing with the wheel installed was available. The refrigerator was at my summer house a hundred miles away. Anyway, we had to grind the end of the riveted axle to dislodge it from the wheel housing. With the axle dislodged from the housing we were able to install the wheel and then hammer the end of the axle flat to keep in place, like the original rivet installation. It is not perfect but it held and should be fine. I am glad I was able to get the part and will be back in the future, if in need of other parts.

It was so easy!

Thanks for the rush to my home on the part.

I just unscrewed the plate that locks in the light switch (screwdriver) and unplugged the old faulty part and plugged in the new switch, screwed the cover back on and I was done!

Easy!

And I am not Mr. Fix-it!

I removed the 3 screws that held the handle on refrigerator, then cleaned up the grime before putting on the new handle, which fit perfectly. The only complaint I have was there were no new screws with the handle. I am a single woman and this was a very easy project for me. I am very satisfied with the product, and with the fast delivery.

Used a screw driver to pull old switch. Pulled one wire at a time, only two wires. After wires instlled to new switch push new one back in place where the old one was.

remove front grill. with pry bar and wooden block, elevate side with broken wheel and insert wooden block behind assemble from the exterior bottom. With roller wheel assemble lose from the wooden block remove front elevator screw from the front frame. next remove cotter pin with the pliers and pull assemble pin. next elevate assemble out. drill out axle on the crimp side insert from the hardware store one 5/16 x 21/2 bolt with nut and new wheel. reinsert assemble in the reverse order. Remove wooden block and adjust height of wheel. replace grill. job complete. good job

I simply removed the old switch using 2 small screwdrivers and the old switch case popped out. I then upluged the wires from the old switch and reversed the process. Didn't take longer than 5 minutes begining to end! Thank you for the great service! Duncan quaid

It was a complete mess and a failure. There were no in structions with the gaskets except warming them in water to streatch them. Nothing with a photo of what the gasket looks like as it is being installed or after installation. I am still not convinced they are the correct gaskets for the model. It was a total waste of time and $130.00 to try to replace the gaskets. In the end, I determined that it would be cheaper in the long run to buy a used refrigerator than to mess with the gaskets.