All Installation Instructions for Jenn-Air Range SVD8310SF

Fan switch on top was broken off inside outer housing rendering all controls useless, worst of the fan.

Cut power!
Removed old switch.Only problem was new switch had shifted the four 'spade' connectiors on back so when I was done fan and light switch was crossed.

Everything PartSelect had on their site was perfectly correct.

REALLY appreciated the way PartsSelect handled everything, I will be back for further help on other things.

Parts Used:

Toggle Switch - With Push Nuts

kevin from wheaton, IL
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Pliers, Screw drivers

3 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Housing of fan switch broke causing the switch to be inaccessable to use

After accessing the switch and removing the wires(four wires as the rocker switch operates both fan and oven light) I attached the wires to the new switch. However , I was unable to mount the switch in place as I could not get the spring - clip type of fasteners to slip on.
Fortunately, there was space to drill a hole on each side of the switch and I used brass machine screws
and nuts to hold the switch. The round-head screw
tops show on top of the stove, but at least the new switch is in place and operating.

Parts Used:

Toggle Switch - With Push Nuts

Gerard P from Poughkeepsie, NY
Difficulty Level:
Difficult
Total Repair Time:
More than 2 hours
Tools:
Pliers, Screw drivers

3 of 4 people found this instruction helpful.

Was this instruction helpful to you?

blower motor

removed blower housing secured to floor with two screws then removed flexible vent pipe from blower housing then removed blower removed blower wheel and motor put new motor and wheel on put back on stove thats it..

Parts Used:

Blower Motor Kit

david from central city, KY
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Screw drivers

3 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Blower was stopped up and running extreme slow

Took parts off from under the range, and replaced the motor. Then put the unit back under the stove and connected the vent.

Everything went fine. No trouble.

Parts Used:

Blower Motor Kit

Allan from Searcy, AR
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver

4 of 8 people found this instruction helpful.

Was this instruction helpful to you?

Front burner wouldn't light because hole burned in metal tube that channelled gas to burner

So very easy!!!! I'm a 70 year old grandmother with a small socket set - and that's all I needed! Removed one small screw, removed old burner, popped new burner in, replaced one screw, and back in business! Placed order, received it in 2 days, fixed burner. So much faster than calling a repairman!

Parts Used:

Range Front Burner Assembly Black (Glossy Finish)

Linda from BOLIVAR, TN
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Socket set

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Front burner would not light

Removed old burner, replaced with new one, works perfectly! Only one screw to take out and use with new piece.

Parts Used:

Range Front Burner Assembly Black (Glossy Finish)

Patricia from COLORADO SPGS, CO
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Light bulb and socket became one when trying to remove a burned out bulb. Ruined the socket.

Move stove out from wall. Unplug from power. Removed four screws from the left side of the back (the side the light socket is on. Reach in and unplug the two wires on the back of the bulb socket assembly. Inside the oven, remove the bulb cover and the two screws holding the socket assembly. Remove assembly. Install bulb in new assembly, reattach the assembly to the oven back, reinstall the bulb cover. On the back of the stove, replug the two wires and replace the screws on the stove's back cover. Replug the unit to power and move back into position.
Sounds harder than it is. The worst part is reaching inside the oven to get at those bits.

Parts Used:

Light Bulb Socket

Light Bulb - 40W

Byron from LE SUEUR, MN
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

This item needed replacement for the 3rd time due to finish wearing off, within 6 months EACH time.

unscrewed previous unit, placed new unit and screwed in place.

Parts Used:

Range Front Burner Assembly Black (Glossy Finish)

JoAnn from Raleigh, NC
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

The oven light went off, changing the bulb did’n’t solve the proble, beacause the socket was burned.

First thing
disconnect from electricity
Remove the back cover by unscrewing its fixing screws
Using philips screw driver, To remove the scocket assembly, pull the tow electric wires from the socket, using a fine plier.
Open the oven door and unlock the glass cover and remove it.
Remove the 2 screws fixjing the socket from inside the oven.
Now the socket is ready to be disassembled by just pushing the clips with tow fingers.
Replace the socket and do same steps in reverse way.
insert the lamp, and the glass cover, connect the electricity and you are done.

Parts Used:

Light Bulb Socket

mohd fouad alahdab ruh from JAMAICA, NY
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers, Socket set

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Knob broke on range

Simply removed old knob and popped on new knob. No tools needed.

Parts Used:

Gas Valve Knob

Patricia from COLUMBUS, OH
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Switch for fan was heat damaged and broke

Removed top plate, disconnected old switch... Had to go to hardware store to get different push washers - the ones supplied with the part were too small. connected switch... tested connections and replaced top plate.

Parts Used:

Toggle Switch - With Push Nuts

Christopher from Wilmington, DE
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Replacing the bulb in the freezer side

Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.

Parts Used:

Light Bulb - 40W

Yafa (and David) from Bothell, WA
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

5 of 11 people found this instruction helpful.

Was this instruction helpful to you?

The painted finish on the pan for my range started flaking.

Called Parts select and they replaced it in two days.

Parts Used:

Double Burner Pan - Black

Burma from Section, AL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Front burner inoperative

Simply removed the front burner using 1/4 incn nutdriver on
two screws.placed new burner in position and tightenwd two screws.
Simplest and easiest job I ever did!
Works as new!

Parts Used:

Range Front Burner Assembly Black (Glossy Finish)