RSS307 Caloric Range - Instructions

Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.

I slid out the oven burner disconected the old igniter and replaced it with the new one & slid back in place and connected the two wires and I was back in business. The job was relativly an easy one.

My husband took the oven door off then the bottom piece below the shelf took the old ignigter out put the new on in and now I have an oven again.

Replaced the existing ignitor by removing the bottom drip pan/gas line/ignitor (apprimately 18 screws), unscrewing the wire nuts, removing the old ignitor, connecting the wires to the new ignitor, and reinstalling the drip pan/gas line/ignitor (18 screws).

Un plug elect. Cord. Remove door by pulling upward removed back stove panel, un did 2 wire nuts leading to igniter. Un screw igniter inside oven at top next to burner pad. Interchanged old ignitor with new plug stove back in. Thats it.

For the third time in less than a year I had to replace the broiler igniter. The range is 27 years old and has given us excellent service. When the igniter failed it's replacement lasted 3 months. The next replacement lasted about 6 months. This last replacement has been in service about 1 week. We shall see. The last one had an open wire within the ceramic mould. There was continuity from one wire, through the black portion, but not to the second wire. It seems like it was a fault in manufacturing.

Although this was not a repair I wanted to let you know your service was outstanding and the price quite reasonable. I am very happy to finally have a much needed second rack in my oven that was not there when I purchased my home. Thank You

Followed Instructions with part. Easy Install. However the problem not solved. I believe Oven Control defective (Worn Out). Replacement May not be available. Still looking. Thank You. RJC

Removed old ignightor and installed new one

Ceramic connectors were taken off the old igniter, pulled off old igniter and replaced in the same way the new igniter

Daughter and family came to visit Gramps for the weekend; Saturday morning, arose and opened a couple of cans of grand buscuits. Set aside to let rise then turned oven on to preheat. Came back later and oven did not work. Stove top worked, broiler worked, but no oven. What to do, didn't want to waste dough; perhaps salvage for dumplings, no; make poorboy doughnuts, no; Aha, lets use the outside gas grill, never done it, worth the try, remember old camping days except using gas. Worked like a charm, crisis over. Now back to oven. Since everything worked except the oven burner problem could be in the igniter, or oven control. Removed covers to burner assembly, pulled igniter, checked for continuity across the two leads. No go. Wait, need to check oven control, placed voltmeter across incomming leads, turned oven controls on and had voltage. Conclusion, igniter bad. Also noticed a small rust hole in the burner tube next to igniter, not good. Went on-line to PartsSelect, entered make and model number. No model but gave choice close to model. Viewed pictures, found one that came close. Placed order. Parts came in a very short time. Matched new parts to old. perfect. Removed burner tube and installed new one, one screw, simple. Wire nut the incomming leads to igniter and install, three screws, simple. Turned oven on, igniter glows bright, gas comes on, good blue flame, no need to adjust air inlet vents on burner tube. Turned off oven, replaced covers, then turned on oven, baked cornbread and enjoyed. Thanks, back in business. Dave

We actually had to get the repairman back that had repaired our microwave. Our range has the attached microwave above the range. My stovetop light worked prior to the visit. When he left, I prepared supper without the light, which did not go on. Ultimately, we had to replace the fluorscent tube, which thankfully, you had. No appliance store in a 35 mile radius did. We finally got the glass protector off, and the new tube did not go on. Back to the repairman, to tell him the new bulb did not work and that probably something happened when he visited before. He came back, found that indeed a wire had been broken when he was working on the microwave. I had indicated to him I did not expect to pay another repair bill after I had alrealy spent 117. before plus the cost of the new bulb, 22. something including shipping. He obliged and id not charge me anythink to repair the broken wire.
Now I have the old bulb for back up!!!
Thank you for having my replacement tube!!

shut off gas at tank, pulled stove out from counter area to gain acess to back, removed oven door removed removed screws holding igniter unit in place, i then removed the stove rear panel to get at the wiring for ignitor,remoded old part returned to front and installed new part, checked voltage then re-connected new wires, turded gas back on and tested oven, oven came on less than a minute, put rear panel on stove put door back on and put stove back into counter area, stove works like new.

The first one came damaged and customer service credited the first one and got another on the way the same day. They were awesome to deal with. I removed the oven racks, the burner cover, the storage drawr, and the door. That took about 5 minutes. I removed 3 screws that held the ignitor in place. I removed the 2 wire nuts from the wires in the drawr space. I slid the ingitor cover off the old ignitor and onto the new one. Slid the new ignitor into place and fed the wires below and put on the 2 wire nuts, then installed the 3 screws and tested the operation. I put the oven back together and put the tools away. Total time about 20 minutes.

Removed burner with attached igniter assembly by raising forward legs from slots and pulling unit from rear support. Note: this is contrary to instruction #1 on installation instructions. Then followed the remaining instuctions 2 - 7 as written. Everything worked as planned.