REP309A0W Gibson Range - Instructions

took the screws out and then put the new element in and that was all.

Pretty easy installation; you lift the top plate up and snip the wires maybe four inches away from the burner. Leave more wire than you think you need; once you get into it you'll realize you need more wire length than you think.

Then strip the remaining ends, twist them together with the provided caps, and use the heat shrink to hold it together. Remove the old terminal, replace it with the new ones, and you're good to go!

Remember to check that the wires are tight in the cap before heat shrinking, though. I had to get more shrink wrap in order to finish.

Took out bottom drawer and unplugged power cord, slid unit out to reach back panel,removed front door( 2 Phillips screws) making it easier to reach back of oven, removed screws inside of oven holding element in place, took plate off rear and removed the spade connectors with needle nose pliers. Slid new element into oven and replaced screws inside of oven. Connected the two spade wires on the back and replaced rear panel. Slid unit back in place and plugged the 220v power cord back in. Straightforward and very simple! It took 3 times longer to clean the oven while it was disconnected than it did to replace the element.!

It was simple.............the range-top tilts up so I proped it with a stick of wood, pulled out the old burner and plugged in the new one (when I saw how inexpensive the new element was I orderd two to replace the other 8" because it didn't look long for this world either). The whole operation took less than 10 min. no tools or batteries required!!!!!!!!!.........no-mus-no -fus.

Your prices were the lowest I found on-line, keep up the great work!!!!!!!!!

I pulled out the stove from the wall and unplugged it. I then used a socket set with a long extension which made it easier to reach the rear wall of the stove. After removing the screws i gentle pulled the element forward and exposed the clips and wires. I removed the clips. The wires seemed to want to slip back into the hole so I used clothes pins to hold them in place. After I received the new element (Two Days) I reversed the process. Using a socket set it is very easy to tighten the screws to much. Be careful to just snug the screws. I plugged the unit back in and slid it back in place and turned it on.

Removed the old & simply inserted the new one

Plugged the new one in and it worked.
I did search out Frigidaire parts and there are other types tha may or may not work. Calrod burners are not all that unusual. I went with the real thing.

I unplugged the dead burner and plugged in the new burner. Very easy. No tools needed.

Cut the old block off tied new wires to hot wires . That easy!

Removed back cover, unhooked wires, unscrewed and removed bad baking element. Reverse order to install. Less than 15 min. repair job.

First unplugged the stove, then removed the screws holding the element in place. Next I pulled the element out until the wires were visible and unplugged them. After removing the old element, I plugged the new one in and positioned it with the screws. Plug the stove back in and done.

snap out the old one and snap in the new

Removed element by loosening two screws, disconnected heater element and connected new element and reattached to oven wall. Turn on oven to check for heater to work. Confirmed heater worked. Repair complete.

I turned off the circuit breaker to the range. Next I removed the two screws that fastened the element to the rear of the oven. Then I pulled the element out far enough to be able to reach the spade clips and disconnected the element. I connected the replacement element to the clips and fastened it to the rear of the oven with the two screws. I turned the circuit braker on and the element functioned properly.

Really easy process. First I unplugged the oven for safety then I proceeded to remove the 2 screws that were holding the old element in place. Next I removed the old element then installed the new one. After installing the two screws I connect the oven back to its power source and BANG!............. It works like a charm

I give it a A+ installation