REP309A0W Gibson Range - Overview
Sections of the REP309A0W
[Viewing 1 of 1]
Keep searches simple, eg. "belt" or "pump".
Terminal Block Kit
PartSelect #: PS470125
Manufacturer #: 5303935058
This surface burner terminal block kit comes with interchangeable mounting brackets, terminal box, ceramic wire nuts, heat shrink protective tubing and wires.
$24.46
In Stock
Surface Element - 8 Inch - 2600W
PartSelect #: PS2339242
Manufacturer #: 316442301
This surface burner element is eight inches in diameter. It has five turns, 2600 watts and looped terminal ends. The element provides heat to the cooking surface on your range. If your element is not ...
$54.46
In Stock
Bake Element - 240V
PartSelect #: PS453960
Manufacturer #: 5303051519
This heating element is a partially open-style bake element. Carrying 240V and 2000W, it is 19-1/4" wide by 15" long. The two 90-degree push-on male spade terminals are 13-3/4" apart.
$58.11
In Stock
6-Inch Coil Burner Element
PartSelect #: PS2368974
Manufacturer #: 318372211
This element has looped terminal ends and comes with a black medallion center. This element is a genuine OEM replacement part, has looped terminal ends, comes with a black medallion center, and fits m...
$45.77
In Stock
Broil Element
PartSelect #: PS453959
Manufacturer #: 5303051516
This fully open fixed oven broil element carries 240 volts and 2750 watts.
$219.98
Special Order
Common Symptoms of the REP309A0W
[Viewing 6 of 6]Element will not heat
Fixed by
these parts
these parts
Show All
Little to no heat when baking
Fixed by
these parts
these parts
Show All
Will Not Start
Fixed by
these parts
these parts
Show All
Oven not heating evenly
Fixed by
these parts
these parts
Show All
Oven is too hot
Fixed by
these parts
these parts
Show All
Little to no heat when broiling
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Baking Heating Element Burned Up
Used a screw driver with a socket head to remove the two hex head screws holding the old element. Pulled the old element forward until the two wire attachements were visable. The wires were attached with a simple tab connector. Removed the wires from the element. Attached wires to new element slide the element and wires back into wall of oven and replaced screws. Done!
Parts Used:
-
Christopher from North Salt Lake, UT
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Socket set
193 of 202 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
blown bake element
Removed the two screws that hold the element in place at the rear of the oven.Unplug each prob,you may need pliers as they can be a little tight.Reconnected the new element.Keep the old screws.New element does not come with screws.Always unplug range when doing repairs.
Parts Used:
-
joseph from washington, PA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver, Pliers
59 of 62 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
burner shorted out
I followed the directions by clipping wires to old burner socket, splicing the wires to new terminal block, screwing down new "block bracket," and plugging in new burner.
Parts Used:
-
David from Encinitas, CA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
61 of 75 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!