RB6360N3 Hotpoint Range - Instructions

1. Bought replacement part said to replace old switch.
2. Pulled old switch out.
3. Replacement part did not match. Would have to take entire switch panel apart to change to this part.
4. Multiple-part instructions very poor. For my switch unreadable.
5. Old part was "push to turn". New part was not.
6. Knob did not fit new switch. Old shaft was "D" shaped. New is square.
7. Gave up. Need to call repair shop.
8. Hope this helps.

turn off electricity to stove and simply remove the screws from the heating element and put new element back in place .put screws in and turn power back on and test.

I just replaced them.

I took out the old broiler support bar, but it was being held by one screw. I did install the new bar with one screw, but I need to obtain a second screw. I still have not located a second screw, but it is inplace.

Installed new knobs, mom is happy!!

apply liner on bottom liner of oven

Partselect made this job a breeze. Due to the user friendly process to order and receive the part. I repaired the stove after turning off the breaker in the main box. There were two screws that held the baking unit in place, removed them and then replaced with new unit.

Got new part! Unplug range!!!
Remove oven door by opening and lifting up at the same time, set aside.
Remove two screws with a nutdriver or screwdriver.
Pull on element far enough to unhook wires and throw away old element and install the wires on the new element and reinstall!!

Removed existing surface element and replaced with new element.

P.S.

Part Select service was excellent.

Lifted burner element to remove pressure on ring and drip bowl. Removed old parts and replaced in reverse order. This not intended to sound sexist, but my wife who is not particularily mechanically inclined performed the task on her own.

First removed oven door, according to Reader's Digest repair manual, then removed two screws holding element. Pulled element out several inches, then removed one side of bracket holding up front of element so that bad element could be pulled further out. Then disconnected two red wires from one side and two light blue wires from other side. Removed old Element. Attached two light blue wires to one side and two red wires to other pole, inserted element back into rear wall and attached with two screws, Re-attached bracket holding up front of element. Re-installed door. Tested and it worked fine.

I removed the unit easily with anut driver, however the unit also supported the thermo-link. I had to use the hack saw to relieve a small opening for the thermo-link to pass through. No real problem. Then a few holes to be drilled to attach the 'link' to the base of the broiler unit.

BUT-I went into the website listed on the box. GEAppliances.com Guess what? Their price was twice yours!!

When the part arrived, I used the diagram provided by the website to see what really needed to be done. Keep in mind, if you're doing it correctly and disconnect the range from the power source, it's going to be dark inside the oven. Get a good flashlight or electric lantern. There are two screws holding the element in. Mine were 8MM hex-head screws, but be prepared for anything. I removed the with a socket attachment/adapter to my cordless drill/screwdriver, and the part came right out. Some insulation will come as well - don't panic. Installation is similar, just in reverse order. Pay attention to the feet on the element. Make certain they are down. Don't lean on them when you think you're finished and discover that you installed it upside down like someone I know, and have to pull it out to correct this.

Broiler element arrived at my door 3 days after ordering which was nice. Apparently the billing dept. is out of the USA so don't be surprised, like I was, to find a suspicious looking charge for a currency exchange fee (mine was 42 cents). I had to drill two new screw holes in the base of the new element in order for it to fit my oven. I also had to use heavy wire snips to cut off about an inch of the top of the new element base. The female electrical connections also had to be spread out with needle nose pliers since the new element connections were slightly thicker. With all of the issues I had I was frustrated and it took about two hours. On the other hand, the part works perfectly and was priced right. Hopefully it will fit perfectly out of the box for your oven.

I had already removed the worn out part. The new part came with wire joint covers and connecting them was fine. The brace that came with the part did not actually fit onto the stove burner well; so I cleaned and used the older brace - but, when I went to put it back in place, the bearings on the original self locking bolt were stripped. So, I had to find a replacement bolt with a nut. Found that I had some of those on hand. Once the brace was firmly in place, the rest was easy!