PDWF680R10SS General Electric Dishwasher - Instructions

The first thing I did was watch the video on the removal of the old broken dispenser and I said to myself that it couldn't be that easy. Well I am going on 70 years old and I was going to call a local to fix it. I bought the new dispenser just to avoid the up-charge. When the conformation email got here with video and written instructions. I watched the video and read the instructions. Just after the part arived (ahead of scheduls) I looked at the machins and said wat the he** what is she going to do to an old man. Got my screwdriver (battery and reversable) and wouldn't you know it . It only took me less then 15 minutes to do the whole job. I can't thank them enough for the video. Wife asked where the part was and almost pased out when I opened the door.. lol Trust these people . They know what they are doing!!!

Flipped washer on side
Did repair from bottom
Really easy repair

Inserted new cap purchased from PartSelect.

Attached the drain hose to the dishwasher pump and to the sink pipes and I was done.

I watched the video that came with email on part. Gave instructions on how to. Thank you !

followed the video step by step which was very well expalined and was able to complete the install

Watched online video, repaired myself in under 10 minutes.
Easy fix with video instructions

Ordered most likely part...water inlet valve.

1. Turn off water supply.
2. Remove the metal toe kick plate/insulation at the bottom of the
dishwasher.
3. Remove hose to supply valve.
4. Take electrical plug off old valve.
5. Remove float valve because it was mounted it right in the way of
the 2 screws on the inlet valve bracket.
6. Remove those 2 screws now you can get to them, and move the
inlet valve to one side so you can get to the hose clamp for the
rubber hose out of the valve going to the dishwasher.
7, Take the old valve and bracket out, mount new valve on the
bracket, crawl back down on the floor, reinstall rubber hose and
bracket, and float valve and finally inlet hose.
8. Turn water on. Check hose connections for leaks. Yep, outlet
hose didn't clamp enough now, allowing a drip.
9. Repeat the whole process AGAIN. Replace little clamp
with a REAL hose clamp, reinstall the thing again. No leak this
time.
10. Test run dishwasher thru a cycle. Check again for leaks at hose
connections. OK ? Reinstall insulation pieces and toe kick
plate.

The Lower Rack was a simple swap. The Upper Rack had a tube and rotating sprayer that had to be removed and installed on the new rack. I used a nutdriver to remove a few screws and reinstall them on the new unit. Very simple.

Ordered new cap and put it on when it arrived.
Simple

I placed the missing cap into the dispenser.

This was simple. I took the door apart with a portable screw driver. Then I detached the wires and unscrewed the old module and replaced it. I then put the door back together, loaded the dishwasher and it cleaned my dishes. Even for this `old dog' it was easy.

It was a very simple replacement. I took the old one out and rolled the new one in. It took less than 5 minutes!

Removed kick panel and pulled out the unit from cabinet carefully. Turned off water and power. Removed the water feed and used an aluminum pie tin line a low-profile drip pan to catch the extra water and used a scrap towel to clean the dust and extra water spilling out. Used sockets and wrench to remove the old inlet and screwed out the housing to examine the old inlet. No real way to clean it. Honestly, I don’t see a reason for the filter. There’s no way to replace it and it’s not easy to change out anyway. The particles were so small they could have passed through and not harmed the system. A better and more practical place for any filter would be just in front of the inlet that could just pop in every 2-3 years as needed preventatively in 5 minutes. Anyway, I reassembled and tested. Water flow was great. I think it cleans better too because the hot water fills the plastic reservoir faster and stays hot to clean more effectively.

Per ps video. Really easy. Disconnect power, Remove front lower panel, remove Power leads, 2 installation bolts, remove 2 spring clamps on feed/exit hoses,reinstall.