PDWF680R10SS General Electric Dishwasher - Instructions

Removed Dishwasher, inverted it and replaced the sump housing. There are 2 screws mounting the top of the dishwasher to the counter, a water connection and the electrical connection. Remember to turn the water off and the electricity off. Slide the DW out on carpet. Carried it to the garage to affect the repair. Reinstalled the dishwasher. Most difficult part of this is that the water hose is really short. I used a 6ft extension so that the next time I have to pull this out it will be easier.

Removed front Door panel, by removing screws from back side of door, replaced pump, door handle actuator & spring. I did not have to remove the dishwasher from the counter (built in). Repairs took all of 20 min. and dishwasher was back in service. The price I paid for all the parts from PartSelect, was less then G.E. Repair Service wanted just to come out and look at the dishwasher ($99.50 plus parts & labor). The parts that online G.E Appliance was selling were about 25% to 40% higher in price. With total cost I figured I saved about $250.00 to $325.00 by doing it myself and the help of PartSelect.

Exactly as described by a previous reviewer. I pulled out the old rack, put in the new rack and just moved over the cutlery rack.

Hint on determining if the Main Conduit is the cause. Place a tapered flat piece of wood (wooden spatula) between the Main Conduit and rear of the dishwasher wall and remove any excess play.
Run the wash cycle and determine if the noise goes away or is reduced.

Removal and Replacement of the Main Conduit Assembly:
Opened the Dishwasher door and removed the lower and upper basket.
The upper basket required the two rubber gourmets on the front of the rail to be removed by inserting a flat bladed screwdriver between the top of white farthest tab towards the rear of the dishwasher of the rack slide end cap (PS2370502 – Item 652) and twist the screwdriver while gently pushing the top of the tab towards the rear of the dishwasher and gently pulling on the end cap (The rear tab needs to clear the upper rack slide).
Repeat this process on the other upper rack slide and remove the upper rack assembly.

Using a ¼ inch socket driver, remove the Main Conduit (PS651676 Item 585) screw located in the back of the Dishwasher wall and the screw from the upper spray arm (PS260547 Item 570) located on the roof of the unit.
Remover the lower Spray arm by gently pulling up and turning it counter clockwise.
Remove the fine filter hub nut (PS259078 item 454 ) by turning it counter clockwise and the fine filter (PS259068 item 452) The fine filter has a small tube going into the bottom of the dishwasher base that should be removed at the same time of the filter. Be sure to position it correctly when it is reassembled.
There is also a small stainless washer in the bottom of the fine filter housing. Take care not to loose it during the assembly and disassebly process

Remove the Main Conduit from the plastic assembly in the drain of the dishwasher by turning it counter clockwise. (Note, the new Main Conduit Assembly comes with this part pre assembled). Remove the same plastic piece from the new Main Conduit assembly by carefully lifting the clip on it.
Install the new piece back in the drain and tighten just prior to being pointed toward the back of the dishwasher.
Reassemble the Main Conduit to the drain piece and tighten it the remainder of the way and reassemble all parts in the reverse order they were removed.

Part was an exact match. Make sure to use plumber's tape on all threads. Had to really tighten fittings to prevent leaks. Screws are a little difficult to get to. Test for leaks first, before final installation.

When I first tried to fix the handle I could not figure out where the spring went. I went back online and looked at the diagram of the dishwasher on this site and learned where it went. Once I knew where every piece went it only took me about 5 minutes to put it back in and another 5 minutes to screw the cover back on. I am a newer homeowner and want to be able to do minor fixes. This was my first one and was very happy that I was able to do it on my own.

1. remove old basket. 2 Place new basket.. Done

Detached the dishwasher from the cabinet. Slid it out. Removed small guide wheel that the cable went through. Removed the old broken cable. Replaced with new cable. Replaced the guide wheel. Hooked the cable to the door. Hooked the other end to the spring and hooked the spring to the body of the dishwasher. Put some WD40 on the the cable guide. Slide the dishwasher back under the counter and attached it to the cabinets. All done.

Lower assembly only require removal and replacement without tools. Upper assembly required screw driver and pliers to install water wand from old rack to new rack.

The most surprising aspect of this repair was the short 36 hours that it took from order placement to product receipt.

Took out old basket, took off the sprayer arm and put it on the new basket.. pulled out the old wheels on the side tracks and slid the new basket in...pretty simple...

Remove screws holding old hose. Attach clamp to new hose with nut driver. Tighten hose and clamp around attachment.

Easy as cake. Perfect part!

Removed the wire clip, then removed two screws on mounting bracket. Then disconected the hose. Removed the brass elbow.

Then reversed these steps and I was done.

No tools required. The seal just pushes into a channel around the tub. The lower ends are held by a wire that spans the lower edge of the door. I started with the lower end since I didn't know just how the seal was installed and found the wire that sticks into the hollow center of the end of the seal. The seal just pulls out so removed it and the wire. Cleaned the seal channel and wire and installed the new seal starting at the bottom and working upwards. after the lower ends are anchored,I found the center of the seal and upper channel and pushed it in place and worked around the corners and down. I did that because I have seen seals stretch as you push them in place and end up in the middle with excess material you have to work back into the seal channel.

I took the front off of the dishwasher door, loosened the screws, unplugged the module and replaced it with the new module. This repair was the easiest repair I've ever completed!

1. Removed the cap ends from the inner rails - easy

2. Removed the old rusted rack from the inner rails- easy

3. Removed the spray arm and conduit - a bit difficult: there's a hard-to-reach nut that you need to remove at the hub of the spray arm - A pain in the neck because it cannot be reached vertically.

4. Installed the spray arm and conduit onto new rack. Make sure the conduit aligns with the pipe at the rear inner wall! - easy

5. Installed the rack onto the rails - easy

6. inserted the cap ends - done!