Models > PDT775SYN2FS > Instructions

PDT775SYN2FS General Electric Dishwasher - Instructions

All Instructions for the PDT775SYN2FS
31 - 45 of 56
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Lower spray arm had melted tips
A quick twist of the locking nut
Parts Used:
LOWER SPRAY ARM
  • Ed from TRAVELERS RST, SC
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
4 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
leaking from somewhere around tub
the actual gasket tub seal was easy, 10 minutes. The trim tub gaskets were a pain because I had to uninstall the dishwasher (not plumbing or electrical) then pull it out from the cabinet, remove old trim and re-install. Re-leveled dishwasher, screwed into side of cabinets but it still leaks. Can't figure out where but after replacing all the trim and gaskets its very frustrating.
Parts Used:
GASKET TUB Stainless Steel TUB TRIMS KIT TUB TRIMS KIT TUB TRIMS KIT
  • jeff from FORT COLLINS, CO
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Pliers, Screw drivers, Wrench (Adjustable)
4 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Door did not latch, therefore would not operate
Replaced latch
Parts Used:
Door Latch
  • Dawn from JAMESTOWN, TN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
5 of 9 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Mid Spray Arm Assembly not spinning
The Mid Spray Arm Assembly was not spinning due to a dish that was in placed the dishwasher that was too high and hitting the arm. When it spun until it broke the center shaft. Replacement was easy. After removing power I pulled the upper tray out and removed the Conduit Mid Tiered Assembly by unsnapping it from the tray. I twisted off the broken spindle of the damaged arm assembly from the Conduit Mid Tiered Assembly and inserted the new arm and gently pushed it until it snapped into the Mid Tiered Assembly. Reinstalled the assembled parts by snapping into the tray making sure it was centered.
Parts Used:
MID SPRAY ARM
  • Robert from FLUSHING, MI
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dish washer would not turn on
took off 2 sheet metal on the bottom, lowered the dish washer, pulled it out enought to unscrew 2 screws, unplugged the old part plugged in the new, put it back together.
Works like a champ.
Parts Used:
Door Latch
  • Patrick from BROOKFIELD, WI
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers, Socket set
4 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dishwasher would not sense door was latched
Super easy repair, just removed the old latch and replaced it with the new one.
Parts Used:
Door Latch
  • Robert from CASEVILLE, MI
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Had to replace the lower arm and adapter
One I figured out how to get the original contraption out, it was smooth sailing. I used pliers because thats all I had, but a socket wrench would have been much easier. The adapter has to be pressed a certain way to pull it out, but then the new one easily snapped back into place, and the nut went in mostly with ease. Again, a socket wrench would have been a much better tool to use.
Parts Used:
LOWER SPRAY ARM S ARM ADAPTER
  • Casey from OMAHA, NE
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Socket set, Wrench (Adjustable)
4 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Loud banging sound when dishwasher was on.
The base of the spray arm literally just spins a little bit into place like a luer lock. Takes two seconds to replace.
Parts Used:
LOWER SPRAY ARM
  • Joseph from KENNEDALE, TX
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Old silverware basket wore through and melamine utensils fell through and stuck to heating element which cost me $100 for repairman to remove
Put new basket in, threw old one away
Parts Used:
Dishwasher Basket Assembly Silverware
  • Diana from NAPLES, FL
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dishwasher tub was leaking
Simply removed old gasket by hand, lined up center of new gasket (white dot was printed on the center of new gasket) with the tub latch and pressed new gasket into place. We have used the dishwasher about a dozen times since and hasn't leaked a drop.
Parts Used:
GASKET TUB Stainless Steel
  • Philip from TOLLAND, CT
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All 3 spray arms were stoped up.
Replaced all 3 spray arms in less than 10 minutes.The top one came in two pieces,the mounting bracket and the arm.Snap the bracket on the dishwasher first , then attach the arm to the bracket.
Parts Used:
MID SPRAY ARM LOWER SPRAY ARM
  • Kenneth from SEBRING, FL
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
3 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
roller wheel was melted.
I removed the old roller wheels and the new roller wheels snapped together and the simple instructions made the repair quick and simple..
Parts Used:
RACK CARRIER AND ROLLER KIT
  • Julian T from Dalton, GA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dishwasher door was leaking at bottom.
When new gasket arrived almost two weeks after it was sent out from Green Bay, I took out old gasket, marking which side was in and which out.
Then, with hands, fit new gasket in place making sure it was centered.
No leaking; it worked.
Thanks.
Parts Used:
GASKET TUB Stainless Steel
  • Neil from NEW YORK, NY
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Old Trim Tub Pieces were bent from an improper installation
I have them to the plumber who was reinstalling a poorly installed dishwasher. Parts worked perfectly
Parts Used:
TUB TRIMS KIT TUB TRIMS KIT TUB TRIMS KIT CT SCREW Assembly
  • Mark from BRUCE TWP, MI
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
6 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
washer would nt ru it beeped 3x and flash start lite
Looked upm the problem it said door wasn.t closed so cause was the door latch. put in the new one no change so I bought a new dishwasher
Parts Used:
Door Latch
  • Robert from ST AUGUSTINE, FL
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the PDT775SYN2FS
31 - 45 of 56