PB975KM1CC General Electric Range - Instructions

Pulled out the range from the wall and unplugged it. (A good time to clean up the cabinet sides & floor.) Found the 2 screws under the cooktop by opening the oven door. Removed the screws and raised the cooktop -- it's hinged in the back. Propped up the cooktop with a spare piece of lumber. (I would have expected to find a fold-out rod to prop it up -- a suggestion to GE.) Noted the positions of the 4 spade lug connectors and removed them gently with a pair of needlenose pliers. Removed the 2 screws from the clips holding the element in place & removed the element. Installation was the exact reverse: clips, spade lugs, front screws. (Then I removed the blue masking tape I had put over the burner knob so we wouldn't try to use the burner while I was waiting for the part to arrive.) Plugged it in & pushed it back in place. Good to go! 30 minutes including the surprise cleanup.

Very easy to remove the parts and to reassemble

I checked various sites on the net and decided that the temperature sensor was the problem. The GE price for the replacement part was about $105, most of the other sites offered the sensor in the $70 range. PartSelect $12.95 When the part arrived, I removed a small self taping screw, pulled the high temperature wire connector into the oven space, disconnected the quick disconnect fitting, attached the new temperature sensor, pushed the connecting wire into its hole, replaced the screw and that was it. I probably saved about $200 in parts and labor over what a local repairman would have charged. Oh yes!! I first disconnected the power at the breaker box. Very important.

Performed repair using a video for reference.

This item worked as described. I paid more for this 'oem' probe than the generic 1 because i didn't want to chance it not working as others have reported.
- works great. tested it....snaps in, reads correctly, snaps out.

Just note the wire colors and match them where they go on the new control, remove and replace 7 screws and a zip tie and I was done.

Took the oven door off and removed the inner door panel, put new glass assembly part in and reassembled. The hard part was getting the door hinges locked back into place.

Sensor is in rear and on top ov oven. What could be a 10" job took 45". My problem was the oven door was diffinately in the way. Also I wear bifocals which makes me tilt head to see nuts. I felt like a contortionist. HINT: remove door and give yourself some room to work.

Removed torx screws for door handle as well as torx screws for both hinges to separate the door halves to extract broken glass and to install new glass panel. Other reviews said not to remove hinge screws, however I had no problem reinstalling them.

Not only did we (my wife did help) replace the dual element but afterwards we realized the control switch was not functioning properly and so that was replaced as well, and now our appliance works as intended. Also the instructions, are helpful as well. We used care not to force or over tighten anything and with two sets of eyes and the extra hands everything went much better. Anything that was removed was noted as to it's location and replaced .

Turn off breaker, disconnect electrical wiring, remove cooktop from courter top, turn over , remove switch.

it went well as compared to getting a new ~~800$ cooktop and ~~150 to install, I took a shot for 30$ bucks and it worked great!! problem solved and great support ! !! thanks for all your help

Pull oven out away from the wall, unplugged from outlet, removed center cover by removing 5 sheet metal screws. disconnected thermostat sensor from control cable. Opened oven door and removed screw that holds thermostat sensor. Pulled thermostat sensor out replaced with new sensor. Plugged sensor in to control cable. Replace panel and screws. Then my wife made me clean the oven. I recommend making the repair when your wife is not home.

took bulb out, but new one in lol

1) Shut off power to oven
2) Removed oven door using snap down hinges on door
3) Removed 4-phillips head screws holding the oven frame to cabinets
4) Pulled oven out of cabinet and set it on stool in front of opening
5) Remove 2-hex screws holding metal shield covering the electrical wiring on back of oven
6) Unplugged bad thermostat connector
7) Removed the single hex screw holding thermostat inside the oven
8) Pulled the thermostat and lead wire from oven
9) Fed the new thermostat wire into inside back of oven
10) Reverse steps 1-7