All Installation Instructions for General Electric Range P2S975DEP3BB

door gasket was soiled

took out old gasket and inserted new

Parts Used:

Door Gasket

Joseph from Murrells Inlet, SC
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Temp probe was defective

Threw the old one out - plugged the new one in. Steak came out just as ordered - medium rare.

Parts Used:

Meat Probe Thermistor

Eric from SOUTHBURY, CT
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Followed a GE Video on installation

Followed GE repair video

Parts Used:

Door Gasket

Sarah from MONTGOMERY, TX
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Oven lamp globe shattered . Needed a replacement

The oven lamp shattered while cleaning. Easy to replace by hand.

Parts Used:

LENS OVEN LAMP

Joan from SOUTHINGTON, CT
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Failed ignighter

Repair is easy. The keeper ring installation while holding the spring down was tricky. An extra set of hands is helpful in holding and replacing the keeper ring.

Parts Used:

Range Electrode Top

Connie from WESTFIELD, IN
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers

1 person found this instruction helpful.

Was this instruction helpful to you?

Plastic guide Broken

replaced Plastic Guides

Parts Used:

Bottom Drawer Guide

NICK from Vernon, CA
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

9 of 25 people found this instruction helpful.

Was this instruction helpful to you?

Food ran over the burner and damaged it.It was easy to place it back inII

It only required placing the new burner in the proper location.

Parts Used:

Burner Cap - Black - Medium - 9500 BTU

Alan from PASADENA, TX
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Sparking at 2 different burners all by themselves

Replaced Spark Module and adjusted igniters

Parts Used:

SPARK MODULE

paul from las vegas, NV
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers

3 of 7 people found this instruction helpful.

Was this instruction helpful to you?

some of electrodes not working at times,found were bad,wires had some insulation missing, clips looked burnt,found all new parts replaced

the electrodes on this model have to be removed before you can raise cooktop, once cooktop is raised remove wire from burner bracket, use needle nose pliers to squeeze bottom of clip,remove &replace with new parts.

Parts Used:

Top Electrode Mounting Clip

Dana from LEEDS, AL
Difficulty Level:
Really Easy
Total Repair Time:
More than 2 hours
Tools:
Pliers

1 person found this instruction helpful.

Was this instruction helpful to you?

The Grate foot is to big for the hole.

I had to drill the hole to a larger size to enable the foot to fit.

Parts Used:

Grate Foot

Harold from Broadalbin, NY
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

The electrode had broke

I unscrewed the base where the electrode was attached to detached the electrode detached the wire to the electrode inserted new electrode with holding spring and clamp attached wire to electrode.
I then put the base back on top and screwed in the two screws assembled the remaining parts and turned on the stove unit and it worked I am very happy.

Parts Used:

Range Electrode Top

O.Robert from Montrose, PA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

gas burners not heating evenly

remove old burner, put new in place

Parts Used:

Small Burner - 5K

Burner Head - Large - 12K

Burner Head - Medium - 9500

Juanita from GAINESVILLE, GA
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Light bulb went out,could not find replacement part.

Turn the glass enclosure counterclockwise to expose bulb.Turn the power off at circuit breaker panel.Handle the bulb carefully with paper towel covering the bulb.Push the bulb in socket.replace glass enclosure,turn power back on.

Parts Used: