All Installation Instructions for Maytag Dryer MED6230HC4

Rollers making a noise.

Removed the top, removed lower front cover, removed the front, removed the belt, removed the drum and the back. Removed and replaced roller support shaft and drum roller’s. Completed all Front and rear support for drum. Replaced drum , replaced drum roller belt and replaced back, completed replacement of the top, front.

Parts Used:

Drum Support Shaft - Rear Shaft with Left Hand Threads WPW10359272

Carl from MARION, KY
Difficulty Level:
Really Easy
Total Repair Time:
More than 2 hours
Tools:
Nutdriver, Pliers, Socket set

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Part broken in half

Remove screws, dryer sensor on screen. Put sensor back in place. Secure with screws. The way you take it off go in reverse.

Parts Used:

Outlet Screen Door Grille

Screw - 10-16 x 1

Sean from ROCK HILL, SC
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

3 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Repair video made it easy

Just follow the repair video, it was easy!

Parts Used:

Dryer Repair Kit

Jack from DINUBA, CA
Difficulty Level:
Really Easy
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Heating element went out.

Followed the instructions all went good except for the sliding the shield back in it didn't want to go back in but it does fit. Dryer works like new again.

Parts Used:

Dryer Heating Element

Charles from SALLISAW, OK
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Very loud squeaking!

Couple screws behind the electrical panel at the top and the top pushed back and was able to remove front panel, and then it was pretty easy. Take the two screws on top front, lint trap screws . The lint trap vent needs to come off. Then the belt, drum comes out to access the idler pulley. I did replace two drum wheels, I saw there was 5. I would recommend replacing all of them, they didn’t move well…..

Parts Used:

Idler Pulley with Bracket

Travis from GARRETT, IN
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Socket set

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

lint screen was not catching lint and sending out the dryer vent

replaced dryer lint screen with new.

Parts Used:

Lint Filter

Scott from WOODBURY, MN
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

HEATING ELEMENT open circuit

replacing the heating element was difficult due to the small area to work with and the defective element was difficult to slide out from housing.

Parts Used:

Dryer Heating Element

High Limit Thermostat and Thermal Cut-Off Kit

Fred from ROCKINGHAM, VA
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Socket set

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

The lint filter needed replacement due to what is probably normal wear and tear.

I searched for a replacement by entering the model number and serial number of my Kenmore elite dryer. Ordering was extremely simple and it took less than a week to arrive. It fits perfectly.

Parts Used:

Lint Filter

Donna from CARY, NC
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Screen ripped

Dropped new filter in.

Parts Used:

Lint Filter

Cindy from BENZONIA, MI
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Not heating up

I just took the old element replaced with the new one i order from this site, I save some money was really easy so proud of my self...

Parts Used:

Dryer Heating Element

braulio from FORT WAYNE, IN
Difficulty Level:
Very Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

dryer was making a grinding noise

I researched causes of the noise, zeroed it down to the idler pulley. I then got the dryer schematic and took the dryer apart after disconnecting the power and the vent. i did not have to remove the drum, the idler pulley was easily accessible once the top and back panels were removed. I simply removed the drive belt from tension off the pulley, removed the old pulley and installed the new one. Once finished the dryer was running whisper quiet.

Parts Used: