MDE9700AYW Maytag Dryer - Instructions

After getting on-line to your site we looked up what the problem could be after receiving the dryer from a friend to transfer from electric to gas to save money. First we thought it to be the ignitor and after receiving it so quickly it still didn't work so went to your site again and found the Flame sensor. They were both defective and now it works wonderful!!! Your site also explains what and how to repair the appliance, which my husband appreciated! We are glad you contacted us because your site did not show that we could send you and e-mail Thanking your company for the excellant service we received. Your prices can't compare to other companies either, we were amazed on the differences. When you say the next day delivery, you mean the next day!!! Thankyou and you are now in my Favorites if ever needing parts for other appliances we own.

On the Amana dryer, I had to remove the top panel. then the front panel to access the burner assembly. I also had to remove the gas pipe coming to the burner, because I replaced the tube burner assembly at the same time. There is only one screw that holds that back end of that gas pipe. The thermal flame sensor is on the left side of the burning chamber, with only one small Phillips head screw. just remove the 2 wires, keeping track of which terminal they belong. Just twist the sensor out of the small slot, and out it comes. The tube burner assembly is fastened with 2 screws. The entire burner assembly comes out in one piece, but be real careful not to bang the igniter when removing it. The coil assembly has 2 wires, which you cannot get wrong, because one has 2 prongs, the other has 3 wires.The local repair shop wanted 90 bucks per hour, plus parts, and I installed both the burner tube and radiant flame sensor for around $80.

Followed the easy to understand how to video. The drier was up and heating again in less then 30 minutes.

I change the Thermistor 3 bracket and worked well for 10 minutes and the thermistor is broken again

*Disconnect power cord before performing this task...(1) Remove the two screws holding top.(2) Remove four screws holding control module, tilt forward, pull up and unlatch. Place module on top, out of the way (still connected by wires). (3) Open dryer door, remove two screws holding lint trap assembly, close door. (4) Remove four screws on top of front cover, disconnect door light wire, tilt front cover forward, lift up from catch at bottom and remove. (5) Disconnect moisture sensor connection on bottom right for easier access to duct assembly. (6) Remove three screws holding duct assembly support bracket in place, raise duct assembly six inches to allow the bracket to be tilted toward rear and lifted out of the way. (7) Disconnect Red and Blue wires from front of duct assembly and pull assembly carefully from the rear of the unit and out the front paying attention to the wires still connected. (8) Remove wires connected to the thermostat and thermistor. (9) Remove screws holding in both units and replace with new components. (10) Reverse process and test. *note* if the unit appears to heat but clothing still wet, make sure moisture sensor was connected (I must have forgot and got to go back in to check, ooops). Regardless, this is an easy task. Could be intimidating at first but after the part has been accessed twice its no big deal and can be done over a lunch break.

Ordered thermal fuse and cycling thermostat

The part came in very quickly. If you know how to remove the front panel, it is very easy to repair. The hard part is to diagnose the problem. The first thing to check is the igniter. If it comes on then you look for faulty limit switches. If you have lots of training in electronics and appliance repair this is very easy, if you do not I would not try this. I have 40 years in the repair business, It still took me 1hr. to find the problem. the switch was intermitted, one time the dryer would work the next time it would not. Good luck and happy repairs.

Remove lower bottom cover (two screws on bottom) with screw driver. Remove old radiant flame sensor from left side of tube with ignior by using socket wretch. Remove wires with needle nose pliers. Put new part in: put wires back on, insert part's lower tab into the tube ( there is a small slot) use socket wrench to tighten screw at top. Put bottom front panel back on and screw back in.

Unplugged dryer from power source, used putty knife to release latches that hold top on, tilted the top out of the way, unplugged door lite, located the radiant switch, removed 1 screw,then undid 2 wires & lifted out switch. Reversed procedure plugged in dryer....wa la had dried a large load of clothes, took 1/3 the time to dry clothes at last. Thanks "PartSelect"

First I replace the Radiant Flame Sensor, but the problem remain. Then replace the two coils and the igniter. Dryer works like it should. If I were to do it over, I would have replaced all 4 components to start with. Thanks for good advice and great service.

Replaced the flame sensor since it was believed to be the problem contributing to the lack of flame in this gas dryer. However, this part did not correct the problem.

Followed troubleshooting steps. Checked thermal fuse (shorted)- OK. Checked igniter (about 70 ohms) - OK. checked flame sensor - (open) BAD (should read shorted). This part is normally shorted then opens when the igniter gets hot causing it to open and thus turns on the gas flow. An open flame sensor does not permit the igniter to turn on.

The Maytag dryer had a removable front panel so it took only about 15 minutes to remove the front, replace the blocking plug and orifice and reinstall the front panel. I gave the repair time as 30-60 minutes since I took the time to vacuum the interior and clean the flame sensor. Great instructions were included with the kit.

Unplugged electrical cord to dryer. removed the front cover 2 screws on the bottom. Lifted front cover off. Unplugged the 2 wires going to the old flame sensor. Used nut driver to remove 1 screw holding the flame sensor in. Removed old sensor replaced with new one. Reattached the 2 wires back on to the new flame sensor. Tested. Flame stayed on longer! Dryer works great dryer is 20 years old and still running like new now. Part was the exact match I needed.

I was working on my daughter’s Maytag dryer model MDE 9700 AYW. The dryer had been making a bumping sound for some time. It had the same symptoms a few years back, but it was still under warranty. The repairman had to replace a drum roller. He told her at the time he should replace all of them but he only had one with him. So when my daughter heard a similar sound she assumed it was a drum roller again so I ordered the roller without taking the dryer part. She has four boys that generate a lot of laundry, so she needs her dryer daily. I wasn’t sure how long it would take to get the part or do the repairs. The roller arrived very quickly, I think in a couple of days. The drum rollers on the dryer did not need to be replaced. What I found was bumping the side to the dryer because the sheet metal had popped inward. The drum has very little clearance on either side. The side probably could’ve used another crease or something to make it more rigid. My time wasn’t, wasted. I think it was will spent. I found that 3+ years of lint at piled up significantly on everything. The lint on the shroud for the heating coil had already turned brown and could have caused a fire. I would suggest to anyone who’s had a dryer for a while should open it up and vacuum out the lint buildup.
It only takes a Phillips screwdriver and very little time. It’s a very little investment for your peace of mind.