MDB100RGW1 Uni Dishwasher - Instructions

Pulled off the old gasket and replaced it the same way with the new one.

Turn off power. Took out screws holding control cover on, (left loose and hanging in the front of the door by the connector wires).Disconnected the two wires at the bottom of the switch. Removed two torx screws, pulled switch out. Reversed procedure to install new switch (which isan exact replacement). turned power back on, tested door latch, washer works perfectly again.

This was a dishwasher that my employer threw out due to the excessive time it was going to take getting the broken part - all of the appliance stores I contacted had them backordered. Since I'm a DIY and Internet savvy person, I decided to go to the Internet page and use the IPB to determine the correct part, and ordered it. I installed the dishwasher, and waited...
10 days after ordering the part, it came right to my door. Installation was very simple; remove 7 Phillips screws from the front panel to access the latch mechanism, remove the two Torx screws holding the latch assembly, disconnect the wires from the latch assembly, and do the reverse procedure to re-install. No latch alignment was necessary, just screw the assembly right back in place. (Yes, I made sure the power had been disconnected!) The door gasket did not need to be replaced at this time.
A very quick and simple procedure for the DIY-type person that can handle simple tools.

I think the videos on the site are awesome. Made both repairs after watching them. They explain the repairs in a simple to follow way.

Removed the two screws that mount to count top pulled the dishwasher out to see how the spring was attached , installed the new spring and the job was done the job it took about 15 mins. to complete.

1. Engage B.R.A.I.N. :
B: Break open the Box. You know you'll never get it back in
R: Read Instructions: It's not more packing material.
A: Assemble New One: Put it together just like the old one
I: Ignore Instruction: Seriously, sharp edges will cut me?
N Never listen to the wife Or at least pretend to be listening

The old gasket was worn. I pulled out the old one, put in the new gasket. I trimmed the ends to fit and that was it.

Took out the two retaining screws and pulled the unit forward. Took the old door strike out and put in the new one. This site is where I go for all my appliance repair parts!!!

New piece snapped right on

First of all, I got the part 24 hours after I ordered it. That in it self was a feat. Second, I followed everyone elses instructions, pulled the old gasket out with a pair of needle nose pliers, cleaned the area as good as I could, found the notch for the slot on the gasket to slide into and viola...it slid in and stayed in. No more leakage whatsoever! Thanks for all of the tips!

Removed 6 phillips head screws that hold the front panel in place...let the panel hang in place...then remove 2 torex screws that hold the handle to the dishwasher ( # 25 torex screw driver needed ).......then pry the wire connections off the old handle..remembering where they go on the new latch.....and reverse the process for the new handle install..and for the gasket just follow the inst's on the sheet that comes with the kit..very easy...but when you close the dishwasher with the new gasket..it's going to be very hard to close..( well for me it was )for the 1st few times...

Viewing the instruction video provided online made my repair process extremely easy. Only thing that held me up was finding a tool to help me remove the torque screws from the latch. Thank goodness for inheriting my grandfather's tools and eventually finding the right bit. The latch came with a new gasket but I recommend not replacing it if it's not necessary. I did replace ours at first but it was too thick and caused our dishwasher to leak. So I placed our original gasket back after cleaning it up and it works just fine. This wife was able to complete this project with two kids under the age of 4 and a hyper border collie running around while the husband was at work.

Completly disconnected and layed dishwasher on its side for better access. New valve support was 1 inch longer than original but created no problem. it took no more than 30 min. to complete job.

turned off electricity, pulled dishwasher out about a foot, turned off water too dishwasher, removed inlet valve and replaced it with new.

I received the parts 3 working days from order. They were in perfect condition and exactly like the originals.
Pulled dishwasher out from under counter. Removed door. Replaced drain hose. Replaced gasket. Replaced springs. Put door back on. Tried rinse cycle. Placed dishwasher back under counter. Works like new.