MAT14CSAWW0 Maytag Washer - Instructions

Replace front legs. Very easy fix.

Replaced hinge switch. Still no spin cycle. Noticed hinge bearing cracked & if hinge forced into switch, spin activated. Ordered new hinge bearings.Spin cycle still didn't engage. On further examination, observed that hinge was bent. Straightened hinge & worked like a charm. Didn't really need new switch or bearings. NOTE : Avoid having washer door bang shut.Took longer than expected, but each procedure was simple.

I press using the plier the spring retainer to removed the two hose from the defective pump.
I used screw driver to removed the two retainer.I pulled the pump away from the shaft of the motor. Replaced with new pump, align to the motor shaft and return back the two retainer. It is easy and its good to have my parts right on time.

Removed the four screws from the control housing. Disconnect wire to machine housing. Remove the two clips connecting the machine housing to the back. Remove washing machine housing. Pump is located right in front. Disconnect hoses, remove and replace pump, reconnect hoses. Replace the machine housing. This was the hardest part if all trying to reinstall the housing.Once you get the machine housing in place correctly, put everything back together. You just saved about $125 in fifteen minutes.

First, I laid the washer upon its back and removed the two clamps that held the water pump in place.
with wire pliers.
Next I removed the two inlet water hoses from the pump and sat that pump aside. I then placed the new water pump upon the shaft of the washer and secured the two water inlet hoses back on the new pump wth the clamps. I tightened them with the wire pliers slipping the clamp upon the hoses. Lastly , I snapped the two wire clamps that hold the pump in place back in their groves and immediately placed the washer up right .

I disconnected the washer from the water supply lines.turned the washer on it's back. took two hoses off the water pump.Unsnapped two spring clip's.Took the old pump off and installed the new pump.That is all there was to it.

Isolated problem to front section of washer by elevating and adding water. Once I identified the pump as leaking (it was pretty obvious:>)I used a screwdriver to release the snaps that hold the pump to the drive motor. After sliding the pump off of the drive motor I used the pliers I release the clamps on the two hoses. Next I logged on to Partselest.com and ordered a replacement. The item arrived in two days. I placed the pump on the motor first then connected the hoses. It was much easier to slide the hose clamps to the proper position with the pump held secure on the motor.

Luckily this washer was in the garage and was being made ready to replace an old broken washer. Being able to lay the washer on its side made the job much easier than if it was upright in the laundry closet.

Removal of the old pump was simply a matter of releasing the two clamps holding the input and output hoses and removing the two spring clips holding the pump in place on the motor shaft.

The new pump install required a reversal of the above and took about 3 minutes. It was a very easy and successful repair.

Simple. Removed two hose clamps, pulled off the hoses, removed the clips that held the pump in place and removed the old pump and then simply did the same thing in reverse to put the new pump in. It was easy and the pump was an exact match.

Had a coworker hold washer tillted back, pop both clips that hold pump in place,with pliers remove clamps from hoses.
install hoses on new pump and install pump on motor with the clips.
It took about 12 minutes to do the whole thing.
It was very easy and fast.

I shut off the water supply hoses and then disconnected them and also disconnected the power supply cord--next I laid the washer on its back being sure to place a block near the water supply valve so the weight of the washer does not rest on the water valve--next I disconnected the inlet and outlet hoses from the pump--next pop off the two retainer clips on the pump and then remove the pump by sliding off of the motor shaft-----to re- assemble just reverse the procedure and you are done--it is a very easy fix.

Just removed the old pump with a pair pliers and snapped the new one on. It was a snap

I made the mistake of ordering the parts without watching the video. I got everything I needed on my order except the special grease that was required, so I had to delay the completion of the repair and pay shipping again to get the grease -- this was my error. The repair was easy and didn't take too long, the video was right on, the parts fit exactly.

Used online instructions from this site

Unplugged the washing machine. Removed the two philipps screws holding the control panel. Swung it up , disconnected interlock connector, and pried the two clips. Removed the top and cabinet assembly to have easy access to the leaking pump.
Disconnected the two hoses connected to the pump. Used the plier to loosen the hose clamps. Removed the two retainers securing the pump. Removed the old and damaged pump and replaced with the new one. Reinstalled the retainers back on. Reconnected the hoses and clamps. Put the top and cabinet assembly back on. Snapped back the clips and reconnected the interlock connector. Screwed the control panel assembly to the cabinet. Done. Ran the washing machine to check for leaks. Found none.