MAH20PDA3W Maytag Washer - Instructions

My 16 yr old son replaced the door boot. He said it was very easy although the wire was alittle tricky. But all in all it was very easy for him. Saved me alot of money.

removed front of washer. loosened two hose clamps. replaced hose. tightened clamps. replaced front cover.

With the video you had on your web site, the repair was very easy. couldn't be any happier. you saved me from buying a new washer!

It was very easy...we ordered the part and it only took a day and a half and it was here.

When I found the WAX motor would not cycle I applied 120VAC directly to the WAX motor and machine went into SPIN CYCLE as it should have. Stopped machine and ordered replacement Machine Control Board. Replaced the part and machine works perfectly.

First and foremost, disconnect the power before anything else, then remove the door, access panel, and front of the washer,I then detached the front of the rubber boot so I could remove the plastic panel that it attaches to, that exposes the springs, I then used a vice grip to remove the springs replacing them one at a time, I also replaced the struts in the rear of the machine which requires removing the rear panel, and I used a bottle jack to support the rear of the washer tub while I changed the struts, I changed the struts first which only helped a little, the springs made the job complete and the washer now completely wrings the clothes to a damp state that dries quickly.

Followed the video, besides the spring, everything was easy.

Follow the suggestions on the rope tied to the side of the washer, then mechanically lever the spring open. Only change I would incorporate is using a block of wood to keep the wash drum from moving over as you pull on the rope to open the spring up. GREAT AND EASY FIX!

removed the door &the top took the tightener off the bellow took old one out put new one on and clean all parts and put it back together works like a new one love it.

Set my iPad on the dryer and played the video. Could not have done it without it. Putting spring back on was the hardest, fell off once. Took that long because video connection timed out and had to get another coffee. Part delivery was quick. Found the drain tube out of the bellows was clogged. If it wasn't for the mildew on the bellows could havw fixed the problem if I had known about a drain at the bottom of the bellows.

On-line instructions were found easily enough. And followed easily. Hard part was placing the cable and spring which secures bellow on drum. One instruction said "you cannot do this by yourself" (I couldn't see how help would have "helped") the other said "this was the hard part" of repair. I weight 115 lbs and it took me 1/2 hour to finally get the spring hooked through cable end it's a very STIFF spring! I only had a short pair of needle nose pliers - an 8-inch pair would have given me more leverage and shorten "hook-up" time.

I just followed what others have already noted. The only challenge was the spring as others have already stated many times. You will need help but be patient and you'll make it work.

My Maytag Neptune quit spinning. I found an on-line diagnostic tree and traced the problem to the wax motor. Testing indicated that the motor had failed even though it was still getting power. The continuity between the wax motor and control board appeared to test good. Based on the apparent diagnostic results, I found PartSelect, read their reviews, and ordered and installed the new wax motor. Once installed, I discovered the new wax motor would not work. I did some more online research .It helped me to find that I had a burned R11 on the control board. It's great for those who want to try their repair skills before ordering a new control board at nearly $350. I I contacted Neptunehelp.com and explained I had just purchased a new wax motor from PartSelect. Neptunehelp sent me the rest of their Stage 1 Repair kit at a discount by eliminating the wax motor in the kit. The kit included solder, a solder wick, a wire to open the printed circuit board holes, and both a new R11 and Q6. The site had a thorough explanation as to why both electronic components should be replaced at the same time...any why both should be replaced if the wax motor has failed. They also had an excellent video on some tricks about installing the wax motor, and an excellent video review on soldering tips if you want to attempt a repair on your own. PartSelect was OK for as far as it went, and the wax motor I purchased now works as it's supposed to. But I hope they will link to the Neptunehelp.com site to assist those who are more adventurous and have more advanced do-it-yourself skills. If you know anything about a VOM and have ever done a little soldering, it may be a better option than buying a wax motor and control board when only the was motor, R11, and Q6 are needed. I've completed the whole repair, including soldering in the new electronic components, and have just completed one wash cycle...the unit now works like new. If you are unsure about your electrical skills, you might want to stick with PartSelect and buy a wax motor and control board. If you're more experienced, and don't mind spending about $50 before having to spend nearly $400, then check out the Neptunehelp.com site for some good one-stop shopping and some good instructional references. They have a couple of contingency plans if the Stage 1 kit fails to fix the problem.

Moldy bellow was the reason I replaced the bellow. It tried cleaning the bellow numerous time over the last five year, but once the mold sets in, it's a losing battle. A highly mold resistant bellow would be nice. The available video was invaluable. I would not have purchased the parts if I had not seen the video. I spent a few more dollars for additional parts, because once I got started I did not want to find a bad part and then not be able to complete the repair in one try. Since the bellow was moldy, I expected the door boot drain hose would be moldy also, so, for a few more dollars, I replace it also. Worth the effort. I took me, just under two hours to complete the job, with the help of my wife. I'm some may be thinking, what did she do? She cleaned the parts I took off, so they were clean, well at least cleaner, when I put them back on. This washer was nearly ten year old and had never been apart. I could have finished the replacement bellow in less than an hour, but I took some time to clean inside the washer while it was apart. That's just the way I roll. Fitting the bellow to seal properly was not as simple as the repairman made it look on the video, but that was because he had done this before, probably many time over. He knew what it felt like to fit it and snap it into place. Once I got the feel of seating the bellow, it went smoothly. The boot cable and spring are a bit tricky to hook, as anticipated; I read some previous experiences. So, I thought about how I was going to secure the spring in order to stretch it to the other cable hook. I decided to use two pairs of vice grips to hold the spring and cable hook end. I have two small to medium sized vice grips, which worked perfectly. Otherwise, it is very difficult to pull and hold a pair of pliers closed, at the same time. I sit at a computer most days and am not used to a mechanics world. Use your brain when you don't have the brawn. Job done, no leaks.

Basically the problem was the bearing replacement. Although you cant get them on PartsSelect, I got the seal kit on the site. The seal kit is easy, the bearings took two days and an air hammer to extract them and a big hammer to get them back in. All in all it was worth it,