MAH14PNBAW Maytag Washer - Instructions

Follow the suggestions on the rope tied to the side of the washer, then mechanically lever the spring open. Only change I would incorporate is using a block of wood to keep the wash drum from moving over as you pull on the rope to open the spring up. GREAT AND EASY FIX!

removed the door &the top took the tightener off the bellow took old one out put new one on and clean all parts and put it back together works like a new one love it.

Set my iPad on the dryer and played the video. Could not have done it without it. Putting spring back on was the hardest, fell off once. Took that long because video connection timed out and had to get another coffee. Part delivery was quick. Found the drain tube out of the bellows was clogged. If it wasn't for the mildew on the bellows could havw fixed the problem if I had known about a drain at the bottom of the bellows.

On-line instructions were found easily enough. And followed easily. Hard part was placing the cable and spring which secures bellow on drum. One instruction said "you cannot do this by yourself" (I couldn't see how help would have "helped") the other said "this was the hard part" of repair. I weight 115 lbs and it took me 1/2 hour to finally get the spring hooked through cable end it's a very STIFF spring! I only had a short pair of needle nose pliers - an 8-inch pair would have given me more leverage and shorten "hook-up" time.

Basically the problem was the bearing replacement. Although you cant get them on PartsSelect, I got the seal kit on the site. The seal kit is easy, the bearings took two days and an air hammer to extract them and a big hammer to get them back in. All in all it was worth it,

Moldy bellow was the reason I replaced the bellow. It tried cleaning the bellow numerous time over the last five year, but once the mold sets in, it's a losing battle. A highly mold resistant bellow would be nice. The available video was invaluable. I would not have purchased the parts if I had not seen the video. I spent a few more dollars for additional parts, because once I got started I did not want to find a bad part and then not be able to complete the repair in one try. Since the bellow was moldy, I expected the door boot drain hose would be moldy also, so, for a few more dollars, I replace it also. Worth the effort. I took me, just under two hours to complete the job, with the help of my wife. I'm some may be thinking, what did she do? She cleaned the parts I took off, so they were clean, well at least cleaner, when I put them back on. This washer was nearly ten year old and had never been apart. I could have finished the replacement bellow in less than an hour, but I took some time to clean inside the washer while it was apart. That's just the way I roll. Fitting the bellow to seal properly was not as simple as the repairman made it look on the video, but that was because he had done this before, probably many time over. He knew what it felt like to fit it and snap it into place. Once I got the feel of seating the bellow, it went smoothly. The boot cable and spring are a bit tricky to hook, as anticipated; I read some previous experiences. So, I thought about how I was going to secure the spring in order to stretch it to the other cable hook. I decided to use two pairs of vice grips to hold the spring and cable hook end. I have two small to medium sized vice grips, which worked perfectly. Otherwise, it is very difficult to pull and hold a pair of pliers closed, at the same time. I sit at a computer most days and am not used to a mechanics world. Use your brain when you don't have the brawn. Job done, no leaks.

Had to remove the door, the face of the washer, and two face pieces between the washer and the stacked drier. I then removed and replaced the bellow. The installation of the new bellow was difficult, the first time. Getting the silicone part onto the tub is tricky as is re-installing the cable and spring. I must have not gotten the cable properly seated on the lower lip as it leaked and I hade to repeat the job the next day. The second time around was much easier. There is a learning curve, even for me, a retired electro mechanical tech. I thing someone who is not very handy would have trouble with it. This repair should be considered only by someone of intermediate or better skills.

Replaced wax motor. You must also replace R11 (3.9 Ohm carbon film resistor (1/4 watt), Q6 Triac (Mouser 526-NTE5656), replaced Jp 18 (jumper) with a fuse (Mouser 576-0251.500HAT1l. This job requires the use of a solder sucker in order to remove parts without lifting up cooper traces.I have had experience with many electronic projects,and could have done this one easier if I still had the proper tools.A solder sucker is cheap, and without it, you will damage the traces. I did, but used a continuity checker to verify I made solder contact with the traces. I have six of these stacked washer/dryers. All failed after about a year of use. I am in absolute disbelief regarding all the stories about how easy this repair is.

This is a stacked Neptune washer. You must take the door, front covers of the machine, plus remove the light and wax motor section to the side. You must disconnect the bleach and softener dispenser connections near the bottom of the washer to get the front portion off so that you can get to the boot. Catch the excess water in a pan to avoid getting the electrical circuit board wet. Take the boot off. This is easy, but the spring that holds the small cable around the boot is a bit tough. You can do this with the needle nose vise grips. Place the boot on the tub first making certain that the small notches in the boot line up properly onto the washer ridges. I had to use a 2 X 2 to pry the tub down so that my friend could get the boot lined up on the tub. Some stretching of the boot is required. Place the cable around the boot on the washer and use a strong mason's cord or similar cord and tie the ends of the cable as tight as you can get it so that the cord holds the cable in place. Place one end of the spring into the cable end and taking the needle nose vise grips pull the spring until it can be placed into the other end of the cable. When finished, take a knife and cut the cord and pull it out. The spring is very strong so it is difficult to pull it into place. Since I am old, I had to enlist a friend who is an appliance repairman to get the spring on. That is the most difficult part. Lastly, you get some dish soap and place around the inner part of the boot where it fits onto the other section of the washer so that you can get it on easily. Reassemble the parts and everything should work OK. Don't remove the plug at the bottom of the new boot unless your washer happens to have the drain connection.

I had pretty much the same experience as others. Difficult parts were 1) removing the inner tub, I used the blunt side of an axe with a 4x4 after several hammers would budge it. 2) removing the old bearing, like others I had to cut them out using a Dremmel with a steel cutting disk from Home Depot ($15) Wear eye protection as sparks are flying! Cut out the inner race and the bearing fell out, then cut V notches in the outer race, trying not to cut into the bearing seats on the tub although I did have a couple small cuts, then hammered it out from opposite side. Installed the new beaings and metal sleave between (what is the sleave for?). I tapped both bearing up against the seat shoulder but with the sleave in between there's not enough room and the new bearings turned real hard as the sleave is binding them. (Minor panic). A couple taps with hammer and chisel on the inner bearing from opposite side to push it out created enough room and the bearings turned real easy. Suggestion; plug the drain opening in the bottom of the outer tub with a towel or sponge to prevent pieces of the old bearing from falling in there. I saw one ball roll down in drain, so I tipped the machine on its side and several balls washed out plus pieces of the old bearing. I had a towel laying over the top but that wasn't enough, needs to be stuffed down in the opening. Re-assembly was easy and the machine runs perfect. The wife is very impressed. Total investment approx $85 (kit, bearings and cutting disk) plus about 8-10 hours vs $800 repair or new machine.

Repair was simpl, took about 3 1/2 hours +. Used on line video for dismantal information & reassembling. Hammered out old bearings and seals. Installed them with big bolt and old bearings, I used the old bearings as pushing tools for new bearings. The large bolt and nut pulled the bearings in to place at the same time. Installed seal and reassembled machine. I moved from Jester to King at home.

The whole thing is on YouTube beating out bearings was the only difficult part

after getting the washer apart and notice that the inner andd outer bearing were bad, I had to beat out the bearing because they were rusted in. after getting the bearings out the washer went together quite easily. It runs like new again.

Thanks to Partselect's accurate parts' lists, and installation video, along with others' posted installation trials, gained confidence to attack problem on my own (coupled with repair (or should I say, "replace")men's advise to trash machine). Bearings had basically disintegrated, causing inner tube to be out-of-alignment, and rub against outer tube. Would just like to add to what others' contributed, that I found Plumber's Tub Drain tool to work very well at knocking-out larger front bearing (was perfect fit to ID of bearing). Had to Dremel cut out rear bearing, but quite accessible from rear of machine. Otherwise, alot of cleaning from 13yrs. of useage. Thanks for everyone's assistance!

Removed front panels, lifted top to open position, removed back cover, removed drive belt, drum pulley, removed rear bearing snap ring, removed seal clips, removed 3 baffels then the 3 mount bolts. Pulled out spinner support and the inner drum. Removed the rear bearing #6206LL with brass drift rod and heavy hammer (came out with little effort. The front bearing #6207LL I soaked with penatrating oil overnight (this bearing was making all the noise as after 11 years water finally got to it) The next morning I had little trouble removing it with the brass rod and hammer, taking my time to work my way around driving it out. After cleaning everything up, assembly was the reverse, carefully driving in the new bearings. The new lip seal was the most difficult getting started without going in crooked. Time spent was a good 8 hours (it would have been more if the outer drum was removed) and the cost of everything was $167.09. Thanks to Part Select, the spinner support assy came the very next day. The two bearings came from Bearing Supply & Depot Inc. The washer operates like new!! Very Quiet!!