MAH14PNBAW Maytag Washer - Instructions

removed door,Opened the front panel, opened the top and proped it out of the way. Pulled the boot from the front cover disconnected the drain, released the boot clamp and pulled the boot off. I cleaned the inside of washer and soap tray. cleaned debris from the drain hose. repaired a broken soap dish connection. changed supply hoses and new valves. Generally checked cleaned and overhauled the washer.

Our rental house washer had the parts removed by the last tenant, just replaced them. Thanks!

removed one panel and front door to access under tub.leak solved!!!! thanks

Bought the parts and just inserted them.

Wow! Thanks to the customer info/hints already posted the repair went super smooth and was relatively easy to accomplish. $70.00 for an easily replaced part sure beats $1,000+ for a new washer. Super fast shipping reduced down-time significantly!!! From start to finish the job took less than 30 minutes. Thank you so much.

Off with the door. Off with the front panel. Lift the top and you are looking at the boot. Remove the boot retaining wire . Remove the boot and reverse the procedure. It's a snap.

Loosened the hose coupling, removed the old washer and strainer; cleaned the opening; flushed the opening; installed new strainer and washer; reattached hose and "Bob's your uncle"! No problem.

Basic disassembly as described earlier.Some tips I found helpfull. Use vice grip pliers on spring.it will keep a grip on the spring hook and you can exert more force to pull the spring.Th bellows was very sticky and hard to slip into place. I put a litle silicone lube ( stuff you use for pool pump gaskets )on the bellows. It made it slip into place easly.

Download machine service manual from internet. This makes dismantling easy and prevents damage to component parts.

Dismantle as per manual and remove old bellow - easy.

Re-install new bellow on tub rim - EXTREMELY difficult. The spring that tensions the wire that holds the bellow in place is extremely powerful and in attempting to stretch it it often slips off the tub rim taking the bellow with it so you have to start all over again. It took me 2 hours to realise I would never be able to do this alone. With the help of a second pair of hands this was accomplished in 20 mins with some difficulty.
The rest of the installation and re-assembly was done without difficulty.

Despite the reviews by people who installed this part themselves, I knew that any type of repair was beyond my ability. I enlisted the assistance of a cousin who is a trained, professional appliance repairman. Despite not having instructions, with his experience things went well until he found he did not have the unique wrench that would have made life easier, but he was able to adapt and use the tools he had at hand. Unfortunatley, after more than twos hours attempting to install the wire around the boot, he realized that he could not do it alone, I had to help him and together, we were able to install the wire. It would have been helpful to have step by step instructions and a list of necessary (or at least useful) tools.

Removed the door and front panel with ease. Then came the spring and cable. People who say it was easy are not telling the whole story. Removing the spring was okay except for it flew across the room. Putting the new cable on with a pair of needlenose pliers did not work for me. I had to get a spring tool like you use on brakes on a car. Once I had the tool and secured the cable in place with a piece of wire I got the spring on. Everything except the spring took about 15 minutes.

I just followed what others have already noted. The only challenge was the spring as others have already stated many times. You will need help but be patient and you'll make it work.

Followed the video, besides the spring, everything was easy.

1. ReMoved spring and cable from tub, 2. Remove bellow drain hose clamp at bottom of bellow, 3. Remove bellow from tub side and door frame, 4. Wet door frame with water and dish soap solution, 5. Press door frame side of bellow into slot. Align grooves, 6. slide tub side of bellow over tub edge, 7. Say a prayer to the good of your choice, 8. Reattach bellow cable with spring. This required use of double stands of 60lb braided fishing line to chinch most of the way and then use of a spring hook took in one hand and needle nose in the other. No less than 12 attempts. Be sure to have another pair of hands ready when doing and the whole job will take about 15 to 20 minutes.

My Maytag Neptune quit spinning. I found an on-line diagnostic tree and traced the problem to the wax motor. Testing indicated that the motor had failed even though it was still getting power. The continuity between the wax motor and control board appeared to test good. Based on the apparent diagnostic results, I found PartSelect, read their reviews, and ordered and installed the new wax motor. Once installed, I discovered the new wax motor would not work. I did some more online research .It helped me to find that I had a burned R11 on the control board. It's great for those who want to try their repair skills before ordering a new control board at nearly $350. I I contacted Neptunehelp.com and explained I had just purchased a new wax motor from PartSelect. Neptunehelp sent me the rest of their Stage 1 Repair kit at a discount by eliminating the wax motor in the kit. The kit included solder, a solder wick, a wire to open the printed circuit board holes, and both a new R11 and Q6. The site had a thorough explanation as to why both electronic components should be replaced at the same time...any why both should be replaced if the wax motor has failed. They also had an excellent video on some tricks about installing the wax motor, and an excellent video review on soldering tips if you want to attempt a repair on your own. PartSelect was OK for as far as it went, and the wax motor I purchased now works as it's supposed to. But I hope they will link to the Neptunehelp.com site to assist those who are more adventurous and have more advanced do-it-yourself skills. If you know anything about a VOM and have ever done a little soldering, it may be a better option than buying a wax motor and control board when only the was motor, R11, and Q6 are needed. I've completed the whole repair, including soldering in the new electronic components, and have just completed one wash cycle...the unit now works like new. If you are unsure about your electrical skills, you might want to stick with PartSelect and buy a wax motor and control board. If you're more experienced, and don't mind spending about $50 before having to spend nearly $400, then check out the Neptunehelp.com site for some good one-stop shopping and some good instructional references. They have a couple of contingency plans if the Stage 1 kit fails to fix the problem.