LSE7806ABQ Maytag Washer Dryer Combo - Instructions

Very Easy Repair! Removed 2 screws at the bottom using a philips screw driver(one on each side). Lifted the cover up to detach. 2 screws at the top were removed using a socket set (one on each side). Old tub cover snapped off easily. Make sure you set the cover the same way as the old cover. The new cover snapped on with minimal force. Make sure it's fully seated. Put everything back together in reverse. Took 20min. Most of the time searching for the tools.

I did it the hard way from the back by removing the motor. The easy way is from the front. From the front there are 2 screws about 5 inches above the floor. Also, remove the 4 screws in the tumbler behind the lent filter. Swing out the front panel from the bottom and it will release at the top. Remove 2 screws on left and right side of the front tumbler cover. It will come out now and you can get to the blower wheel which in my case was just spinning on the motor shaft.

Removed the front panel by removing two front screws. Removed screws from front panel holding tumbler drum. Cleaned interior with a vacuum cleaner. (dryer is at least 16 years old). Removed what was left of rivets on damaged glides with a drill, and cleaned area well. Attached new glides with rivet gun, and also applied glue to make glide and cork more secure. Replaced belts, and decided to reverse drum due to damage to drum from allowing glides to deteriorate to the point of putting scratches on the drum itself, allowing the new glides to rest on drum where there was no damage at all. This process was easy, and fast. We did make one error however, in not noticing that with our model, that there were TWO glides to be replaced. Luckily a local repair shop had one more glide so the job could be done the same day. The dryer sounds like it did when it was brand new. Very quiet! The comments from other home repairs helped very much in clairifying any possible errors. Fast delivery of parts, and the extra help was great. Thanks!

If I had waited until I reviewed the pack-up date that came with the part, the disassembly would have gone much faster. The part arrived in record time, several days before anticipated. Outstanding website, parts and repair experience!

No big deal about replacing a lint filter , take the old one out and put the new one in.

No manual on this so had to remove about 12 screws to figger out disassembly,after locating the right ones[front]the job was easy.Remove front plate,remove drum bearing,remove blower front cover,remove snap ring,remove broken fan,clean fan shaft,slide new fan onto shaft[there is a flat in the bore of new fan]instal fan retainer on stub of fan,reinstal snap ring,reinstal the rest of the parts,test drive system[all sat]The part was exactly as ordered,thanks,Jim Thompson

After turning the water off and unplugging the machine, I took the front panel off the washing machine. I then slipped the belt off the pump sprocket. The pump was right in the front and easy to remove. All I needed was a screwdriver, for the hose clamps, and a 5/16" socket to remove the old pump. I then installed the new pump, with the existing screws, re-attached the 2 hoses, slipped the belt back on, and popped the front panel back into place. The new pump works great and the leak is gone. The whole job onlt took about 30 minutes.

Unplug dryer--remove back panel of control console--swap out buzzer--cover back--plug in--good to go.

Washer originally purchased from Sears. Called Sears for repair. $65.00 to show up. Diagnosed the problem as a Bad belt and pump. Asked for approx. $250 to repair. I declined and ordered a belt and pump from PartSelect.com for half the cost. Took 10-15 minutes to install. Turned the washer on and put it through a drain cycle, it leaked all over the floor. Turns out the only problem was a cracked Outer Tub to Pump Hose. It took about 10 minutes to install. Whala, no leak. Now while I purchased an un-needed pump and belt from PartSelect.com, not their problem. Even though I purchased two items that were not required, the cost was still half of what Sears wanted to charge me for a repair that would not have fixed the problem. I will certainly continue to use and recommend PartSelect.com.

Found noise to be belt slapping the base sheet metal, from being too loose. Belt was loose because the drive pulley was worn and one side of pulley was loose! Used allen wrench to loosen the pulley set screw, and pryed off the old pulley. Replace d with new pulley and new belts. Works and sounds like new!

Lets just say thank god for part select!!!! # 1 By far. This was a one two three job.

Took it apart according to the videos, replaced about all moving parts (almost). Put it back together and still made noise. It turned out to be the blower wheel. Ordered a new blower wheel and installed it. Works great and has mostly all new parts. The website was great!!

I opened the back acess panel and started the dryer. Looking at the motor and idler pulleys it was obvious by the frequency of the squealing noise that it was coming from the idler pulley.
I pulled the retainer clip and tension spring from the idler pulley and removed it. I applied some grease to the shaft and reinstalled the idler pulley.
The squeal was gone confirming that the pulley bushing was dry. I ordered the new idler pulley and when it arrived the next day I cleaned the grease off of the shaft and installed the new idler pulley. Problem solved.

Easily

Our Maytag (A308) washer is now about 29 yrs old. I put in a PartSelect water valve 3 yrs ago. When it started leaking recently I found the cuplrit to be a flexible hose to the outer basis. The front came off easily (two screws at the bottom) and the hose clamps required some cleaning. I recommend purchasing new clamps. Under 30 minutes to get it running again.