LHC4900W1 Whirlpool Washer - Instructions

I followed the instructions I found on your website. It made it very easy. Easier than if I had tried to do it the way I thought I had to remove the back of the washer. Going through the top panel made removing the bottom panel screws unnecessary.
The experts were correct, the instructions precise. Thank you

Your video was helpful. I just followed the directions, replaced the valve, put it back together and celebrated spending $28 instead of the $100 deductible on my home warranty. If you're sure of the part you need, just do it.

Just took screws on top panel holding the gauges pop the spring like braces holding the body of machine to back panel removed water valve one screw unhooked wireing than replaced new valve in reverse order.

The repair went smoothly once I found detailed instructions including pictures on the web. The inlet valve is mounted on the back panel of the machine. To get access to the valve you need to remove the front/side cabinet. This was done by removing the two plastic moldings on the ends of the control panel, swing the control panel back, removing two screws, then tilting the front/side cabinet forward. The inlet valve was held in place by one screw and attached to the washer with a hose clamp. Reverse the process and the job was done.

Shut off the hot water supply (pretty sharp eh?). Disconnected the hose from the hw supply and the at the connection to the washing machine. These had not been touched in at least 15 years and were somewhat tough to loosen but finally came ..... accessibility was a problem for the connection to the water supply as it was in a recessed wall box. Fortunately, we had some washers for the hose connections so the install was a snap. Hardest part of the whole job was moving the washing machine out from between the drier and the wash tub .... tight fit. Thanks for the quick service and to FED EX for their delivery. The delivery fellow was a real gentleman.

Removed top control panel, removed inlet mount hardware, removed both electrical connectors, removed filler hose, Installed new inlet valve in reverse order. Works fine !

I followed the video instructions to the tee. Took more time to move the machine out and put back than to replace the inlet valve.

unlike the other's that said to take the top control panel off, i turned the machine up side down and was able to reach the valve from the bottom. it does require a good reach in but an average length arm will make it. just take the rubber hose loose from the valve with a pair of pliers, or hose clamp pliers if you are so blessed to have them, then pull the hose loose from the valve, then take the two electrical conectors off noting wich one goes with each side, then a nut driver should remove the valve without difficulty. installing new valve should be the reverse. i was up in running in minutes. it took longer to undo the hoses and reattach the hoses than to replace the valve.

The repair was simple as you can imagine. Thought I could buy these legs at any big box store or at least at the local hardware store. No such luck. Partselect had the right product---easy to order and easy to install. Things around here are great.

took off the rear panel and removed the existing inlet valve and installed the new one. Replaced the rear panel and the machine work better than ever.

turn off hot and cold water faucets,unplug the power,pull washer out to gain access to rear cover, remove the top control panel screws,push back and lift off, disconnect hot and cold water hoses from inlet valve and remove enough screws from the back panel to remove the valve, disconnect the valve from the tub fill hose (mine had a spring type hose clamp) note the orientataion of the hot and cold hoses and the solenoid connectors for the hot and cold sides,(mine is stamped in the rear cover)reconnect and reassemble in reverse order and check for proper operation.

Removed the hoses from the inlet valve. Removed screws that hold control panel in place . Removed control panel which exposed two clips that hold the top of the back panel. Removed the ground screw freeing the ground wire, removed the plastic loom which holds a bundle of wires. I next removed the plastic plate that protects the fill valve from splashed water. Removed the screw that holds the valve in place, then removed the wires and the fill hose. Reversed steps to put back together.

First I turned off the water to the washer and then removed the hot/cold water hoses going to the washer, unscrewed the water hoses from the washer, and cleaned the wire screens located immediately inside the inlet water valve. This did not solve the problem. Second, I loosened the hex head screws on the back panel of the washer. This allowed me access to the valve. I tested the valve solenoids with my ohm/volt meter and all checked out OK (but this did not make sense). Third, I surfed the web to find out if the symtoms of the washer's problem were the same as experienced by other people. I found several reports of the same symptoms, all which were solved by replacing the water inlet valve. This conformed my original diagnosis although the valve tested as OK. Fourth, I ordered the part from PartSelect, and removed the hose clamp and two mounting screws holding the old valve to the back panel of the washer and removed the old valves. Last, when the new valve arrived, I assembled the new backing plate to the new valve, attached it to the washer's back panel, attached the water hoses to the valve after fitting new rubber seals to the inside of the hoses, and reattached the washer back panel. The washer is working perfectly again.

took part top of washer saw switch replaced it not to difficult it is always easier when you have new one to look at

First, I unplugged it and disconnected the water hoses (the water has been off to it for days). Then, I tried taking off the back of the washing machine. This didn't work, and I actually ended up googling instructions and found pretty detailed, illustrated instructions at Popular Mechanics.
You need to unscrew the front panel that contains all of the controls first, flip it up, and unhook it from the back of the washer (via an electronics clip and 2 metal clips). The outer cover can then be taken off. I recommend undoing the internal hose next -- I used adjustable pliers to squeeze the connecter and loosen the hose. Then, unscrew the water inlet valve and take it off.

Putting everything back together literally just means reversing the instructions.

My washing machine is on a raise service, and I still haven't gotten the outer frame completely back in place correctly, but it's not touching anything or creating any problems. It's really only to safeguard parts anyways, so no worries if it's not perfect -- at least it works now!