KSM180LELB5 KitchenAid Mixer - Instructions

Replaced gears and cleaned and re-greased gears

1. Removed the mixer from the base by removeing the pivot pin at the mixer base support. 2. removed the retainer ring from the housing. 3. removed the pin from the shaft. 4. removed 5 philips machine screws from the round base. 5. removed the round base from the mixer housing. 6. removed the o-ring from the shaft. 7. removed the shaft and large worm/pinion gear from the shaft. 8. pressed out the pinion drive gear from the mixer. The reverse operation repaired the mixer to new condition.

Remove the mixer head from the base by removing the 4 Phillips head screws. Pry off the ring around the rotating part with a flat head screwdriver. Punch out the pin holding the rotating part and remove. Remove the trim strip by removing the two Phillips screws at the rear of the unit. Remove the 4 screws at the bottom of the mixer head. Carefully separate the bottom of the head from the top using a flat screw driver. There will be the power wires connecting the top to the bottom of the unit. It is best to disconnect these wires to avoid breaking them during rest of the procedure. There will be a lot of grease in the gear box of the mixer. The assembly holding the damaged worm gear can now be removed by removing the three screws holding it to the bottom of the mixer head. At this point I removed the grease from the worm gear assembly to allow better inspection. Punch out the pin holding the worm gear to its shaft and remove the shaft. The worm gear is now free and can be replaced. Add some extra grease to the new gear and reassemble the mixer in the reverse order.

I dismantled the machine to find the problem and to see what part I needed. Than when I ordered the part I saw the video of how to do it. If I had seen the video before I dismantled, I would have save a few steps. The video was very complete and accurate even it being an older model

Knob fell out of the front of the mixer into the bowl and jammed the beater. This caused the motor to strip the plastic worm gear. Open unit to investigate and found about 4 teeth missing out of the worm gear. Ordered a replacement. Installed the new gear once received in about 30 minutes. Wife is now happy again. Just need to make sure you pack enough gease into the new gear before reassembling the unit.

removed one screw from back cover, loosened two screws holding speed control plate, removed one wire at a time from old unit to new, screwed two top screws back on mixer,plug mixer back in, adjust speed control screws until I reached correct speed, put back cover back on

I removed the cover off the back of the mixer. Carefully remove the cardboard gasket around the outside edge. Unlock the nuts that hold the two adjusting screws. Count the turns to remove each screw in order to keep the right adjustment. Pull the plate away enough to remove the control board. There is one long and one short wire that gets plugged into each side of the plate. Watch the location of each wire to make the right connection. Reattach the screws to the proper position. Then install the gasket and rear cover. Check for proper operation.

Order part through parts select. it only took 3 days to receive part. The mixer was very easy to take apart and to replace the gear. it was back together in about 20 min. The video from kitchen aid to repair the unit is awsome. Thanks

Replacing the base retaining bracket(what KitchenAid calls the screw cap) solved the problem immediately. The entire replacement effort took no more than a minute requiring removing 3 screws, discarding the old base, putting in the new one, and putting the screws back in. PartSelect was very easy to do business with. They shipped the part the day I ordered it and it arrived as scheduled. Can't be easier than that.

and I thought replacing the hinge pin would fix it, I used an awl to push out the old pin then used the new pin to push the old one all the way out. That did not fix the problem. Went to a store to look over a new one and saw that the screw under the head at the hinge point on the new machines was not screwed in tight. Turns out that screw is the "bumper" for the head against the neck, so the head is held back by the screw. FIXED

Placed pin in the hole...some wiggling had to be done for a tight fit. Installation complete!