KRSF705HBS00 Whirlpool Refrigerator - Instructions

I took off the broken tube and attempted to order a new one with the confusing we sight at parts.com- after 3 attempts I finally got the right part with help from the operator at parts . Com( nice and helpful) but had to ship wrong parts ( the 2 wrong ones) back. The parts were of good quality and we're not hard to put on

Everything went as planned except the cold temperature (freezer door switch located inside freezer) made deflection of the switch locking tab difficult to remove. Letting the switch warm up was not an option.

In the bottom of the refrigerator cabinet is a small drain that should allow any extra water to drip down to the bottom pan of the refrigerator where the compressor is. The compressor is warm and will evaporate the water quickly. If that drain gets clogged then the water will eventually spill out onto the floor. These parts are not necessary to fix the leaking water but when you open the cabinet to check around, you’ll find a lot of mold and fungus has grown on the Styrofoam because of the wet conditions. So I replaced the Styrofoam holders that secure the heat exchanger. This is easily done by removing the white plastic cover in the back of the refrigerator, and then wiggling out the two Styrofoam holders on the left and right. It’s a little easier if you have the new parts before you remove the old parts because they have to fit in just right, but it’s easily figured out. To clear the drain, it’s a little difficult because the tube makes a nearly right angle just below the drain hole. I was not able to clear the clog by pushing anything down the hole because it just hit the right angle turn. I found that I had to pull the refrigerator out, identify the tube by reaching in the back of the refrigerator toward the bottom, pull the tube straight, and then jam wire up through the tube to clear the clog. You can also buy a tube replacement but replacing the tube requires getting into the back of the refrigerator also, so both are about the same level of work.

When the snack pan is packaged there are two plastic bags located on the side rails of the pan they are filled with a thermoset foam to trap the pan in the shipping container. If not enough foam is placed in the bags or the box is placed on the ground with the rear side down in a forceful way the pan can come loose from the foam packaging. The shipping container had no damage on the outside. There was no marking on the box this side up or fragil. One of the rear ears of the snack pan had broken off about 1" from the end.

Removed old filter then insert new filter and pushed door closed

Eased the putty knife under the edge of the switch housing and pried it off. Pulled two wires off the old terminals and hooked them onto the new one and reinstalled into the refrigerator body.

Pried out the old switch and installed the new switch.

We looked up the problem online with the model number of the refrigerator. We ordered the part and followed the video installation that was sent with the order and was found online prior to purchasing

Repair was tremendously easy. All I did was remove old light switch by prying out with screw driver and plugging in the new light switch and pushing it into the hole. Simple! The instructions weren't needed, but they were very thorough.

Had to push the light switch to get lamp to light up.
Removed power from refrig. and removed old light switch
and replaced with the one I got from Partselect. Turned power back on and was done.

bulbs were not burnt out. received the new switch in a few days. watch the short video, was good to see how it comes out. used a putty knife to release the defective switch, removed wires put them on the new one and posed the new switch back in. Not bad Part cost $11.00 7 dollars shipping so for 17 bucks it works great. nice to see what is inside the refer!

The best part of the repair was how easy it was to find and order the part. Instead of searching the parts houses around town I just went to the PartSelect web site, quickly found and ordered the part in about five minutes, received the part the next day at my home and was ready to make the repair. Wow! What a pleasure for something to work the way it was meant to. Removed old switch located by prying out with sharp knife or screwdriver. Don't worry about breaking it or cracking plastic. Disconnect(unplug) wires from back of switch. Replace (plug-in) wires on back of new switch. Insert in location of old switch. Finisheed.

installed new parts

replaced electric control board, defrost for six hours. next day (24 hours) same problem, [email protected]

A very cold and brittle switch in a 17 year old fridge. Used screwdrivers to pry out with some resistance Had to cut the molded plug in half and split wires, because replacement contacts were farther apart than the original. End result, works great.