Models > KRSF705HBS00 > Instructions

KRSF705HBS00 Whirlpool Refrigerator - Instructions

All Instructions for the KRSF705HBS00
76 - 90 of 149
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Side freezer LED light not working
There are 3 tabs on each side of light that fit into hole in freezer. Pushed putty knife under edge of light. Inserted 2nd putty knife midway down. Push both putty knives in toward light and gently pry up 1st knife until plastic clip is released. Remove 1st knife and insert near bottom and push in. Pry up mid level knife and unit should pop ou. To install just puch new LED light into hole.
Parts Used:
LIGHT
  • Richard from HARRISON, TN
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    15 - 30 mins
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The lights were out in the part of the refrigerator and freezer section of refrigerator.
I ussed meter to check the voltage levels and they were fine. I refrence a you video on the refrigerator and foud out that the lights are setup in series like christmas tree lights. If the freezer light is out it will affect the rest of the lights in the refrigerator. I removed the freezer light module and test the light by swapping it with a know working light. the freezer light was the culprit that took the lights out in the side panels and the left side of the refrigerator section. I replaced the freezer light and all the lights now work without issue.

One light and they all go out. So i used one fo lights
Parts Used:
LED Module Service Kit (White) Refrigerator Air Filter
  • Carlos from CHARLOTTE, NC
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Nutdriver, Pliers, Screw drivers
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The main light in fridge short circuited and the LED lamps would not come on
Literally just unplugged the old light and removed three wire harnesses. Then installed the new light by reconnecting those three wire harnesses
Parts Used:
LIGHT LIGHT
  • Rajeev from NAPERVILLE, IL
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The door switch was broken so the interior light would not come on.
The instructions in the package were not helpful. They wanted me to cut the wiring harness and described where to cut based on the wire colors. My wires were not the same color! I removed the light mechanism using a combination of a screwdriver, putty knife, and plain old muscle with my fingers! The wiring harness unplugged easily and the new one inserted. It was easy to push the whole assembly back into the door. I spent more time looking for something to cut the wiring harness with (and never did find it) than the whole job actually took without needing to cut anything!
Parts Used:
Door Switch
  • Catherine from BROOMALL, PA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Light switch on door broke
Popped out broken switch with blunt flat edged instrument. Disconnected switch from unit . Plugged new piece in and reinserted into side panel of refrigerator. Very easy.
Parts Used:
Door Switch
  • Donna from Oro Valley, AZ
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
3 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broke light switch while cleaning
use kitchen knife to pry out. replaced switch assemble and pressed back into place. Could not have done this with out help from previous customers. Thanks
Parts Used:
Refrigerator Door Switch
  • Gail from Golden, CO
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
No ice
6 screws removed and part replaced
Parts Used:
Refrigerator Ice Maker
  • Alfred from LA PUENTE, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver, Screw drivers
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Freezer drawer light switch failure.
Disconnect plug from wall. Insert putty knife between light switch.and trim panel , apply pressure to depress plastic spring holding switch in place. Apply a slight twist too putty knife releasing switch from trim piece. This wil expose plug connected to switch. Disconnect plug from switch. Connect new switch to plug. Insert switch into trim. Plug refrigerator into wall socket.
Parts Used:
Door Switch
  • HARRY from FSTRVL TRVOSE, PA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Light out.
Popped out the old switch and replaced it with the one dying
Parts Used:
Door Switch
  • Carlton from CHICAGO, IL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Light switch broke
Pried out old part with screwdriver. Unplugged. When new part came, just plugged it in and pushed the part into place.
Parts Used:
Refrigerator Door Switch
  • Carolee from Spokane Valley, WA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
No problems
Just plugged it in
Parts Used:
Door Switch
  • Richard from PORT JERVIS, NY
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Changed the filter
Took the old one out and put the new one in
Parts Used:
Refrigerator Ice and Water Filter
  • George from Port Orchard, WA
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
3 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Filters needed replaced
I ordered the filters that were needed and received the wrong items. After reordering and then receiving the proper items the installation went very well.
Parts Used:
Produce Preserver Filter Refrigerator Air Filter
  • Steven from CEDARVILLE, AR
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Light rocker switch broke and refrigerator light couldn't go on.
I just popped out the old switch with a flat head screwdriver. Removed the connections and then installed new switch by reversing steps. Popped in back in and the light went on.
Parts Used:
Refrigerator Door Switch
  • Cathy from HOPATCONG, NJ
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Refer lights not working, there are two lights and neither worked. Decided the switch was the problem.
The switch fix but did not fix the problem. I assumed the wires go on the same way as on the old switch. Is it possible if one light Burns out, the other will not work either?
Parts Used:
Door Switch
  • John from AUBURN, CA
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the KRSF705HBS00
76 - 90 of 149