KFIL27CXMS4 KitchenAid Refrigerator - Instructions

Tough part was diagnosing the problem: bad water inlet solenoid, frozen inlet line, bad ice maker motor, or door opening sensor? Went to a parts shop & discussed the problem with the serviceman. He said you just need to sequentially replace each part. No way say I, that could cost $300 with a no-part return option.

I decided to replace the motor...Eureka!! It worked.
The underside of the ice maker cartridge has a plastic snap clip on either side of the cartridge. You need push each up, pull the left side of the cartridge out part way & disconnect the electrical connector on the right side(left..you facing the refrig.) With the cartridge out simply remove the 5 screws from the motor plate of the left side & replace with the new one.
Very simple. Slide the cartridge back in the frig. until the 2 snap clips click. Voila...you done! Cost $86..not $300. Apparently the motor is too weak to do the job & burns out quickly. Manufacturer should correct this defect.

installed new parts

Opened up the door that covered the filter, unscrewed it and put the new one in and closed the door back up.

Thought I was going to have to replace entire ice bin but went on this website and saw I only needed to replace a coupling. Even had video on how to do it. Easy greasy!!

The best part of the repair was how easy it was to find and order the part. Instead of searching the parts houses around town I just went to the PartSelect web site, quickly found and ordered the part in about five minutes, received the part the next day at my home and was ready to make the repair. Wow! What a pleasure for something to work the way it was meant to. Removed old switch located by prying out with sharp knife or screwdriver. Don't worry about breaking it or cracking plastic. Disconnect(unplug) wires from back of switch. Replace (plug-in) wires on back of new switch. Insert in location of old switch. Finisheed.

Used a philips screwdriver.

Shut off water supply. filter is located in the upper right hand corner of the refrigerator on the inside. open the drop-down door. by hand pull the filter downward. then twist it to the left one quarter turn. it should pull out. I replaced it with a filter bypass plug. you can purchase a high quality filter to replace.it don't buy cheap filter.I made that mistake! hope this helps good luck!

replaced ice and water filter

I used a knife blade to slip under the edge of old switch to pray it out of the hole it was inserted into, switched the wires and replaced the new switch into the same hole. It took about five minutes!

Extemely easy to install. I just found the model number on ther refridgerator, ordered the part, the part was shipped very fast, installed the Coupling with a small screw driver in less than 5 minutes! I saved myself a lot of money! I am a female and it was very easy to do!

I removed the ice bin and on the bottom of it I removed 1 screw. I put the washer and drive lug on and reattached the screw. It was so simple I thought I surely left something off. It has worked fine since.

The ice dispenser stopped turning for crushed/cubed ice out the chute. Turned out it was this little $10 metal coupling part that broke apart. I'm guessing its not an unusual problem because the partSelect part was redesigned to be thicker than the original part to help prevent it from happening. I was very impressed with the superiour quality of the replacement part.

The old coupling was no longer in the unit so I took out the set screw inserted the new coupling and reset the screw and now my ice maker works again like a champ. Less than 10 minute repair but took an extrea 5 as I had to mnake a new washer that goes under the coupling for wear resistance.

Removed the screw at the base of the ice bin unit. Replaced the coupling that had broken teeth and screwed in the new one. Was very simple. With service call with part near $150 the repair was made for less than $20.

Simply removed screw, replaced coupling and screwed back into place. Took less than a minute. Good as new!