KFCS22EVMS8 KitchenAid Refrigerator - Instructions

The Condenser Fan Motor was already removed due to searching for the problem. The new fan motor looked different from the original but I felt very comfortable that Part Select had sent me the new part showing original part number changing numbers over the years. Simply placed the fan blades onto the new motor lined up 2 of the holes placed screws and tightened then plugged the wire ribbon into the Condensor Fan Motor, plugged in the Refridgerator and it worked beautifully.

The instruction video on the Part Select Web Site made it so incredibly easy to install. Installation took under 3 minutes!

The new door just popped into place. Took seconds to complete. Fast delivery too.

Followed directions on filter unit

Take out the elbow fill tube and check to see if ice build up inside tube. Clean tube of ice build up. Replace tube back in. In my case that corrected my problem.

The installation video for condenser fan motor helped a lot to know how to disconnect the old fan motor and connect the new one. So easy just know how to remove and put back the fan gently, observe carefully where is the center and the connector position; 15 min after everything was done and the unit works well to date.

Ordered left side end cap from Parts Select. They sent me the right side end cap. Had to return the part. They did refund the part price but it cost me shipping both ways. Had to order the part from another vendor. After receiving the correct part it took 19 minutes to remove some shelves, replace the part and replace the shelves, deli drawer and deli cover. Very easy.

Checked a video on YouTube and found questions and answers to this concern.. All lead to the compressor capacitor. Entered part # on your Website. Capacitor come right up and also suggested a Start Device. I ordered both parts as I was not sure if these parts would fix my problem.
R/R rear panel, found Capacitor and replaced it... Compressor came on and refrigerator operated correctly after defrosting Evaporator coils..

Followed the instructions in the video provided via email from Partselect
However, the part received was the opposite design of the part removed.
It appeared this could be left hand right hand choice of part. Moreover, the button on the switch that turns the light off/on when door is open/closed was not functional due to the part being the opposite of the part I was replacing. I tested the switch I was replacing and it appears this is not the problem. I think the light socket is the problem. I am 69 year old female and capable of doing small repairs, but limited knowledge of electrical so having to troubleshoot by trial and error. Thank you.

Popped out the old switch and replaced it with the one dying

Open and remove lower cover on filter holder by opening tabs that hold lower cover and remove lower cover.

Firmly hold back of unit and firmly hold and turn filter in counter clockwise to unlock and remove.

Install new filter by holdin back of unit and install new filter by turning in clock wise direction and then replace lower cover.

Followed the demo film on line.
Good instructions

Checked Video online. Had to remove the 2 snap on track/gear covers. Pry out the gear with screwdriver and the gear bearing unit. Align the flat side of the bearing unit and snap in. Position the cut teeth on the gear to match original and snap into the bearing. Insert the connecting rod into the long shaft gear and then push back into the short shaft gear. The video said to remove the drawer front but I did not and don't see that it necessary.

This problem is caused by a "Duckbill" rubber grommet attached to the bottom drain tube of the freezer. This duckbill opens up during the defrost cycle and allows water to drain down the "water slide" to the evaporator pan. It doesn't take much to gum the Duckbill. Once gummed up the defrost water is trapped. The Defrost Cycle eventually makes the water flow out of the coil area to the bottom of the freezer then eventually to the floor. The repair involves unplugging the unit, removing the bottom back cover with a 1/4 nut driver, pop the power clip out to give you room, reach in and pull the duckbill grommet and the water slide, then installing this replacement drain kit. This is a p trap replacement that actually fixes the root cause of this problem. A tricky part is removing the water slide, you can see the white snap that holds the slide in place. Using a small flat blade from the top releases the snap and the unit is pulled upward rather easily. This replacement drain clip snaps in the same place. If I had to do this again it wouldn't take more than two minutes to replace. Oh, one major thing, you need to manually defrost the unit. I pulled the front door off, it is held with 4 screws ... don't remove them just loosen them and it pops off easily. I pulled the bottom tray out an it gave me room to squirt hot water with a baster into the back freezer area. Eventually everything thawed out. If I had it to do over I would have waited on connecting the tube to the evaporator pan and placed the bottom of the tube into a small sauce pan or something to collect the drain water and easily dump it into the sink. I used a sponge and that took forever. BTW, just to reiterate, use this item and not that Duck Bill for replacement, this actually fixes the root cause of this problem!

I found the instructions on line which seemed very simple but I soon learned otherwise. The instructions say to remove the water line and then firmly pull the fill tube out as it is a tight fit. I couldn't get the tube out and ended up removing the lower freezer door/tray, the upper tray and the icemaker where I found the water had frozen solid in the end of the tube. I used a hair dryer to melt the ice then I could easily remove the tube. After several attempts to install the new tube I finally inserted a 3/8" OD flex tube thru the passage then I was able to slide the new fill tube over this and get it in place. I then reinstalled the icemaker, upper tray and the door/tray assembly. Turned the water on the check for leaks then plugged the unit back in and all is working well.

The switch fix but did not fix the problem. I assumed the wires go on the same way as on the old switch. Is it possible if one light Burns out, the other will not work either?