JVM1490WD - Instructions

I just pulled out the old, and reinstalled the new one.

Placed the new tray in the microwave.

Opened the lid over the bulb by removing one screw. Removed old bulb; a bayonet type with delicate prongs. Inserted new bulb. Best to turn off circuit breaker toi the micro for safety reasons.

It was so easy to order the part on this website. It came carefully packaged and quickly! Thank you!

Received my replacement Tray,Glass in only 2 days. Opened it and placed it in the Microwave. Yep, it was that easy!

Took the tray out of the padded box, and put tray in microwave. That easy, no tools required.

opened the access door. It took some tugging to get the old bulb out, and is was awkward getting the prongs on the replacement bulb lined up and pushed in, but it was accomplished in about 10 minutes. You had exactly the right information on a change in the part number that was made by GE, and you shipped the correct bulb the same day I ordered it.Good job. N R Brown

it work ok now

I'm writing because I have never in my life had such an easy time finding a part, ordering it, and receiving it! Your service is truly unbelievable. I still don't believe it and I experienced it. Nothing went wrong and it could not have been easier. Please don't go away.

First unplugged the microwave, took top grill off, took control panel off, took wires off and used color coded tape to make sure they went back in right places, took fuse out and replaced it and put every thing back and it all worked fine and to top it off my wife did it all. So it was pretty easy.

Removed outer cover and then replaced the T. C. O. located on the left upper side if the unit. Replaced outer cover, tested oven. Oven operates normally.

Removed cover, diagnosed problem, ordered part from Parts Select, received part in 2 days, replaced part, tested and replaced oven into built in space.

On March 21st my wife's daughter and husband and I tackled the repair. I am physically limited, so their help was not only welcomed but necessary.First, removed two screws on the top of the oven to remove the vent panel. Then removed the door by lifting up (as described by others). Next removed the black plastic trim from around the window, using a table knife to pry it loose. Broke off some of the clips but that proved to be no problem at reinstallation. Removed 6 small screws holding the window assembly, but we were unable to pry the plastic tabs loose and we never were able to remove the panel. The screw to the upper end of the door handle is exposed and easily accessible. The screw holding the lower end of the handle is underneath the metal window assembly. We drilled a hole in the metal assembly until the screw was exposed. Removing the screw was a major undertaking. The housing in which the screw was imbeded would not release the screw. We used the drill with a small bit to drill the plastic out until the screw came free. It was difficult and tedious and time consuming. After finally releasing the two screws we began installation of the handle. We found the female receptacle on the handle was very reluctant to accept the screw, both top and bottom. The job was eventually completed after we lubricated the female receptacle adequately. Even so the handle is not quite a snug as I would have liked to have it.The job was hard, tedious, and took over two hours. reinstalltion of the door was no problem. I don't believe the designers and manufacturers intended amateurs to make this repair

Our GE Profile Advantium 120 Series Over-the-Range Microwave stopped working. We called GE Service. The first available appointment was two weeks after our call. The technician charged $99, gave us a form stating that the Magnetron and Diode Cable as defective and quoting an additional price of $362 to furnish and install these parts. He said that it would be another two weeks before he could do the work. Instead I ordered the parts from you and had them within two days. The parts you furnished were identical to the original parts in our unit. They arrived within two days. I installed the parts without removing the microwave from the wall. The most difficult part was inserting the magnetron mounting screws into openings in the rather tight space available. I was able to do this by using plastic pacaging tape to hold the screws onto the end of a short Phillip screw, Prior to iserting each screw I pushed it through the sticky side of a piece of packaging tape. I then folded the sticky surface over the shank of the screw. Once a screw was seated, but before it was fully tightened, I used needle nose pliers to pull off the tape. The unit now functions perfectly.

Took off cover , unpluged switches , took off switch assy, off/on test hooped and howlered for about 5 mins .Then laughed about other sites said could get those switches. Just wanted to say I LOVE Partselect. Super fast del , great price. JUST AWSOME!!!!!!!!!!!!!!!!!!!!!!!!!!!!