JJW9530AAS Jenn-Air Wall Oven - Instructions

Open oven, Remove the 4 screws located on top leading edge of the oven. Pull the plugs from the pannel and then using the nut driver remove screws. Reattach plugs- note do not force. Two people- one to hold the pannel while you do change out.

Removed 4 screws from the front panel. Disconnected the wiring harness at three locations. The printed circuit popped out of the framework. Exhanged with a new one, and reversed procedure to reinstall.

Got a bent metal coathook to temporarily release the oven door, removed the screws from the old probe, inserted the new one, and hooked it up, using the one of the plug adapters provided. Problem solved! The oven door latch was now disengaged, the oven would now accept temperature inputs, and the rear cooling fan (which wouldn't shut off) now turned off. That's a lot of things working better for less than $50!

Remove 4 screws above oven door. Lift glass clock display from oven. Remove four nuts, unplug 3 connectors, lift module out. Install new module, reverse removal procedure. Shazam! Like new.

I removed the four screws that hold the control panel in place, unpluged the three wire connectors, and removed the clock assembly by removing four screws that hold it in place. Next I replaced the four screws that hold the clock in place, pluged in the wire connectors, and replaced the control panel. It was a very simple task.

installed part,turned unit on-temp still cold. reset digital control, up 35 degrees, still cold. un-plugged unit,re-connect after 10 min. still cold.

Unplugged the range, removed screws holding the old sensor. When I pulled it out, the wire connecting to the sensor was completely broken through,therefore I could not just pull the wire to get to the connector. Unscrewed one side of back panel to access the connector. Pushed the connector and wire of the new sensor through the hole ( and behind the insulation), disconnected the old sensor and connected the new one. Re screwed the new connector in place plus rescrewed the back panel. Plugged the range in and - Viola! Everything now works like a charm and I have my oven back. Easy-Peasy. Oh - I am an older female with very limited DYI experience. I just saved myself $650.00!

My daughter & I followed the instructions in your video and had fun repairing the door. The video showed exactly how to do the repair. I hope I don't need any appliance parts very soon but I will certainly pull up your web site if I do. Thanks for an excellent instruction video.

John - Hot Springs Village, AR

Extremely simple repair to make. Move stove away from wall and disconnect power. Remove the oven racks. Remove the rear sheet metal panel covering the wiring harnesses. Caution: Sharp edges and corners on sheet metal.Sensor is located in upper left corner on rear oven wall. Using a long-shafted #2 Philips screwdriver, remove the two Philips head screws and gently pull the sensor 1" away from the oven wall. At this point, it will help to have an assist from someone while you are behind the range. Have the assistant gently tug on the sensor while you watch for wires moving on the rear of the range. After locating the sensor wires, gently disconnect the plastic connector clip. Note: plastic connectors become brittle with age and exposure to heat Move to front of range and gently remove sensor from rear wall by pulling the wiring through the oven wall. Before inserting the new sensor wire through the oven wall, "dry fit" the wiring connectors to see that the new sensor is a correct connection. Make connection, and secure the sensor to the rear oven wall with the two screws. Install racks, reinstall rear sheet metal panel, and connect the power. Set the oven baking temperature to a moderately low temp, 300 - 350 deg. to test the new sensor.

I removed the two mounting screws and pulled the harness through the opening unsnapped the sensor from the harness and installed the new sensor i didn't have to used the adapters the new sensor fitted

I removed 4 screws on the under side of the glass that held the clock assy. removed the glass panel and removed 3 connectors off the back. Removed the 4 screws holding down the clock assy with a nut driver. Put the new part in place and it was back together in 3 min. Easy Peezy I would of felt foolish hireing a repairman to do this job....

Open oven door, remove four phillips screws, lift off the faceplate. Remove circiut board containing the readouts with nutdriver unplug two connectors and install the new board. Very happy with results and saved a bundle !!

Repair was just exactly like a dozen I read before I ordered the part. Turn off breaker. Remove 4 phillips head screws on the bottom of the clock face. Tilt out from the bottom, take out 4 screws with 1/4" nutdriver, unplug 3 wiring harnesses. Replace in reverse order and turn the power back on.

Turned off power to the oven. Removed the four screws on the bottom of the control panel. The panel then needed to be lifted up just a bit to release from a bracket that holds the top in place. Because this is a built-in with a microwave oven above it I had to remove four screws to take off the decorative facade from around the microwave.

Once the surround on the microwave was removed I slide up the control panel. Removed 3 cables from the timer and the 4 screws holding it in place. Installed the new timer (4 screws and 3 cables), put the control panel back in place. Four screws in the bottom of the panel, four screws in the surround and done. Turned the power back on to the oven and 2 days later cooked a turkey for Thanksgiving.

Number one: trip the breaker on the oven. Next, I removed four screws from the bottom of the front display panel. Then, unhooked the panel and gently placed it on the counter next to it. Then I un-plugged each of the three inputs and plugged them into the new component. I then unscrewed the four hex screws from assembly and removed the old unit. I reversed the process and screwed it back in, and when I turned on the circuit breaker, everything worked as advertised. Total time: less than 15 minutes.