JGR8890ADP14 Jenn-Air Range - Instructions

I removed all the screws that held the trim and inner frame to the outside window unit first. Then, I removed a protective glass from over the two inner panes. Next after removing the frame that held the two inner glass panes together, I took the broken inner glass pane out and replaced it with the new one. Then basically I just retraced my steps and had the door put back together in about 45 minutes. You just need to pay close attention to your disassembly so that you are able to put the pieces back together quickly.

The repair went very easy. Just took out the old set and put the new one in. The most time consuming part was to take off the outer parts of the stove to get to the part I needed to repair. The repair was easier than I had expected.

replaced heat sensor

Door was removed very easily. Outside trim pieces were removed. The rest came apart like a simple puzzle. Inside glass is very easily accessed. Upon assembling, time was well under an hour. Shipping was fantastic and I saved close to 200dollars between a service call and a repair.

I located the temp sensor (top left). Removed the 2x Phillips screws and slide the wire out until the plug is thru the opening taking care not to pull to hard as to damage the end that you not going to replace. To install plug it in and push the wire thru and secure with 2x Phillip screws.

Watch the video. Spot on instructions. Easy peasy.

To replace the igniter, I removed the oven door, all racks, the cover for the burner element and the shield over the burner element. I also removed the back panel to access the wiring. Removal of these elements was easy and took only a couple of minutes. When I tried to remove the old igniter from the bracket supporting it, one of the screws was stripped. Unfortunately I had to drill this screw out and replace it. If I didn't have to do this, both jobs would have taken about 20 minutes combined. After removing the igniter from the bracket, I replaced it, ran the electrical to the back where the wiring harness was and reassembled the components.

As for the upper oven temperature sensor, it took 5 minutes. I removed the two screws holding the sensor in place and pulled it out which exposed the electrical connection. I simply unplugged it, and screwed the new one in its place. I then connected the wiring harness.

Remove the door.
Remove screws
Clear out broken glass. Vacuum out small glass shards.
Clean all glass.
Reattach all parts.
Replace the door.
Smile!

Simply remove two screws take old one off and line up and put new one on and replace the two screws. Couldn't have been easier.

Hired a pro. Parts are difficult to get on a timely basis today , if at all. Screw up this repair by damaging the outer " black glass " and you buy a new stove. It took three weeks to get my replacement glass even though PS said the part was being sent within a day of the order. Even so , I am am happy to have gotten it , and will continue to use the company.

After reading from a Google search, why won't me maytag genius double oven light? I read that my oven will not open its gas valve until the igniter is hot, glowing red. Mine didn't glow red bad igniters. After ordering the new parts install was easy and under 15 mins. My advice is to be careful pulling the oven out to access the back panels, be careful not to scratch your flooring. 5 screws for the big panel, and 3 for the small panel. All Phillips head screws. 5 inside the oven to pull the old igniter. Easy job anyone can do it. I did both upper and lower ovens and the broiler igniters.

Unplugged the old temp sensor at the back of the stove. From the inside I removed the 2 retaining screws. I taped a string to the old wire and pulled it through so I could pull the new harness through on the new sensor. When the new sensor arrived I installed it in reverse order. Easy peasy. Works great!!!!

Removed all the racks from inside the oven, unscrewed the 6 screws that held it into the cabinet, pulled it out and sat it on the floor in front of the cabinet. Removed the oven sensor from the inside of the oven after disconnecting the wire harness from the rear right exterior of the oven. Installed new sensor from inside (2screws), plugged it into the harness in the back and reinstalled oven in the cabinet.

The ignitor heated up and the broiler worked but not the bake mode. Repaired per instructions

I received my glass panel realy quick from Part Select. It was an eansy job to install the new pane.
It took less than an hour. Thanks for Your prompt service.