JGR8890ADP14 Jenn-Air Range - Instructions

Removed door, dissasembled door cleaned all broken glass, installed new glass, re-assembled door and put door back on oven.

Very simple project.

Put the back of stove on blocks of wood to get high enough to screw the new leg in.

1. Slowly pull the stove from wall. 2. Unplug 120 volts plug from outlet. 3.Turned off the gas outlet. 4. Open the stove door, remove the racks, then unscrew (2) screws that hold the short oven sensor in place. 5. Slowly pull sensor out of it's housing. Remove the clip that holds the sensor. Install new sensor using the clip. Push sensor back through the hole opening. Screw the (2) screws into the mount to secure the sensor. 6. Plug the 120 volt plug into the wall outlet. Turn on the gas outlet. Test stove by turning on oven. It works like a new stove. Wife is happy, and Thanks Giving Dinner is on! Reverse your steps to secure your stove. A total of 25 minutes after cleaning the dust under stove. Thanks for everything. By the way, Thanks Giving Dinner was delicious.

Remove rear sheet metal cover. Disconnect the temp sensor wiring connector (on the left side as viewed from front).

Open oven, take out the 2 screws attaching sensor and remove. Reverse for installation.

Included wiring adapters are not needed for this model oven.

Removed the original rack. Checked dimensions, installed the new rack.

Replace the racks. No special instructions.

This part was correct, but the removal and installation were complicated by the fact the the gas manifold had two support arms spot-welded into place. These arms hold the gas manifold to the cook-top surface by two machine screws. Also, since I could not budge the screws holding the burners to the cook-top, I could not actually remove the cook-top and had to work in just the space between the cooktop and the top of the oven. The two arms prevented the removal and replacement of the igniter switch assembly. The only way I could remove the old switch assembly and replace it was to bend the two support arms just enough to allow the switch bodies to clear the arms. Then of course, I had to bend the two arms back to their original shape. To do that work, I had to remove the gas supply line (aluminum tubing) from the gas manifold and then reattach the gas line. Doesn't sound too bad, but getting the alignment right on the supply tubing nut was quite difficult. Since there is no lead thread on this male nut, nor on the female connection to the manifold, it is very easy to get it cross-threaded if you are not extremely careful.

I removed the top pulled out oil soaked insulation then decided to clean some of the parts Broke a torx screw on the burner then striped the tube and the burner so had to order the new parts and then put everything back together and it works fine again..It was my fault and the stove has not given me any problems..

Removed old knob, replaced with new one.

Ordered and received the terminal block. Installed it along with a new 220V power cord and the appropriate insulator . Ensured the terminals were tight with a nut driver. Reinstalled cover. Then, using the control panel, I did a function check on all the heating elements, clock, oven light, to satisfy all operational requirements. All checked good! And, I was relieved that the control panel had not been shorted out as the terminal block was due to a loose connection. Easy fix.

easily pulled old seal out and push new seal in place simple and quick.

The repair went very easy. Just took out the old set and put the new one in. The most time consuming part was to take off the outer parts of the stove to get to the part I needed to repair. The repair was easier than I had expected.

I determined the bake igniter was not working. If the bake ignitor does not work, the sensing unit to turn on the gas does not activate. I examined the bake igniter it was blacked significantly in one spot. There were no apperant cracks in it. I did a web search for the part and ordered it. Three days later it was delivered. Take pictures of each step if you fell the need. Pull stove away from wall turn off the gas, unplug power cord, remove panel in back of stove that covers the electrical, unplug the ignitor/element. Move to the front of the range and remove the oven rack. Remove the cover over burner tubes, it secured with several screws. Remove wing nuts for heat shield. Carefully remove burner tubes along with the attached ignitor/element. You will have to carefully guide the ignitor wires out with the burner tubes. Unscrew ignitor from the burner tube, attach new ignitor/element. Reverse the steps.

Once I saw the spring clips on the new door seal, it was easy to understadn how to remove the old seal and install the new one. Looks nice !

Remove two screws back panel and remove sensor two screws inside top oven.