JGP933SEK1SS General Electric Cooktop - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
The Grate Foot was deteriorated on several sections for my cook top. The hardest part was finding the right part.
-
Chelagh from Fredericksburg, VA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
1 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Grate foot bdroke off allowing grate to scratch cooktop
-
John from Tijeras, NM
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
To Replace Gas And Burner Parts In Section 4
Start by removing all screws 3 for each burner total of 15 t-15 bit is required then proceed to remove spark igniters 5 total slight pull next step would be to slide a screwdriver under top left and right side to remove top shelf. There you will have access to the parts you need to replace. When done just reverse installation instructions to complete
Parts Used:
-
John from Long Beach, NY
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers, Wrench set
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
needed new gas valve knobs
Ordered and was quickly shipped and received. Very happy with service.
Thank You,
Donald Torreson
Thank You,
Donald Torreson
Parts Used:
-
Donald from Crown Point, IN
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
0 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Burner Head and Burner Cap were extremely warped allowing flames to come up the sides of pots when in use
Simply took off the burner head and burner cap, and replaced with the new ones. No tools, very simple, less than 5 minutes. Problem is fixed.
Parts Used:
-
Jo Ann from Lisle, IL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
0 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Leaking from front door
First remove the screws around the inside perimeter of the door. These require a special hex driver. Take off the inside plastic liner of door.
Peal off the old Insulation Foam Strip and replace it with the new strip in the same location. Make sure the wires are off to the right side. Replace the door plastic liner. Done. The Insulation Foam Strip really acts more like a loose gasket to keep spashing from creeping under the door and drippin out on the floor.
Peal off the old Insulation Foam Strip and replace it with the new strip in the same location. Make sure the wires are off to the right side. Replace the door plastic liner. Done. The Insulation Foam Strip really acts more like a loose gasket to keep spashing from creeping under the door and drippin out on the floor.
Parts Used:
-
Gene from Simi Valley, CA
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver, Screw drivers
1 of 9 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The spark module would constantly spark
I ordered the spark module and replaced it which was veru simple, plugged it in and it sparked only now and again. I finally said forget it and it has now stopped sparking but for how long I do not know.
Parts Used:
-
Douglas from Knoxville, TN
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Missing grate foot.
-
Barbara J from Sweetwater, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers
Was this instruction helpful to you?
Thank you for voting!
igniter kept igniting
Simply removed the 9 T9 screws from the top of the cooktop, removed the igniter spark modules, lifted the top of the cooktop up and removed harness assembly. Unplug harness from spark module and replaced in same fashion. SUPER EASY done in less than 15 minutes
Parts Used:
-
Jerry from Danville, IL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Both items needed to replace broken or non existent ones
The burner cap was a no brainer. The grate feet should have been also, but many of them were undersized so we had to maneuver them in such a way that they didn't fall out of the grates.
Parts Used:
-
Joan from Warren, NJ
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:15 - 30 mins
Was this instruction helpful to you?
Thank you for voting!
Ingiter Switch shorted; needed to be replaced
TURN OFF GAS and unplug stove. Removed burners (used screw driver to remove screws) and spark ignitors (used pliers). Lifted top cover of stove and unpluged the harness assembly(pulls out easily). Inserted new harness and replaced cover. Replaced burner parts included new spark ignitor. Plug power cord and turn on gas.
Parts Used:
-
Olegario from Whittier, CA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Large burner wasn't lighting very quickly
Removed grill grates, gas distributors, etc. (just lift off). Used star screwdriver to remove screws (3 per burner for SML, 2 for power burner). Lift off stainless cover, which also lifts off the white sparkers I was replacing. Pull them off the wires (didn't need pliers, others said they did). Replace (make sure it is all the way on) and reverse your steps. White sparkers electrodes seemed loose when I put them back on, but tightened up when I fully secured the top back on. Make sure the wires aren't pinched underneath when you put the top back on. Recommended: If you've got one that isn't working, go ahead and replace all 3 (power burner is different) because the part is so cheap you may as well just do it now.
Parts Used:
-
Jesse from Nashville, TN
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
Was this instruction helpful to you?
Thank you for voting!
carbonized burners
Replaced all four
Parts Used:
-
Stephen from North Las Vegas, NV
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
the grate foots came off
put it in but it keeps falling out. they're made narrower than my oven grate.
Parts Used:
-
Sandra from Watertown, MA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Hot Spot On Burner
-
Arthur from Riverside, RI
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!