JCBP24WK3WW General Electric Range - Instructions

Baking element : Pull range away from wall. Disconnect the power. Remove back center panel. Remove range door. Remove range racks. Disconnect push on terminals fron baking element. Remove two hex head screws. Remove baking element. Reassemble in reverse order..........Temperature sensor: with back panel removed, unclip the electrical connector. Remove one hex head screw. Remove temperature sensor. Install in reverse order.

Killed braker first, removed four screws from back, then unplugged all the wiring, then removed four screw that hold the unit on stove, pealed off the face decal, put that on the new on and just reversed the take off press.

Had to move the range out of its little cubby hole in the kitchen so that I could have access to the back of the range. This process probably took the longest. After that it was a piece of cake. Took about 15 minutes to complete the job. So easy, eve a caveman could do it.

Pulled the stove out from between the cabinets, used a blade screwdriver to pop the oven door retainers down and lifted the oven door out, removed the racks. used a 1/4'' nut driver to remove the 5 screws holding the broiler in place. From the time I unplugged the stove from the outlet until I plugged the stove back in was 15 min. I would suggest wearing gloves because the metal frame around the burner element has sharp edges.

Removed screws holding temp sensor, pulled wire out from behind wall until found connector, disconnected old sensor.
Measured resistance of old sensor and compared with new sensor, they measured nearly the same. Installed the new sensor and tested the stove. Came up to temp ok. No problem since, about 2 weeks.

Removed torx screws for door handle as well as torx screws for both hinges to separate the door halves to extract broken glass and to install new glass panel. Other reviews said not to remove hinge screws, however I had no problem reinstalling them.

Replaced Electronic Control Board. Very easy to do with a nut driver and a screw driver to remove the old one. You may need a pair of needle nose pliers to remove Connector TB100 and TB101. Just squeeze the bottom of tabs to release connector. I also found that in the process of removing the Control Board label that it may rip in certain areas even while using a razor blade, so be prepared to purchase a craft paint brush and craft white paint to touch up the back of the label. It took 2 coats but looks like new..

The replacement Control Board works as advertised and I now have my oven working again. Save yourself the cost of a Service Company coming into your home just be prepared to do a bit of painting on the old label because it is really glued down and the new control board does not come with a new label.

couldn't get exact fit--out of production. mounting bracket at back of range for new element too small. took bracket off old element. cut down bracket on new element with tin snips, drilled holes thru it and old bracket and screwed together. at this point the new element was to long & touched oven door. removed spacers that came with new element (used old support to attached to roof of oven) and pried elements apart (which made element wider & shorter). working good.

I knew I had a bad control board. Using the repair videos, replacing this part was very easy to do. While I was at it, I replaced my oven temperature sensor. as well, and even though it wasn't bad, I replaced my oven heating element so that I could get some more mileage out of my 14-year-old range. The issue: after completing my repair actions, my oven element still would not heat. I double-checked my connections and I discovered I hadn't ensured one of the wires on the control board was properly seated. This was one of the wires that go to the heating element. After ensuring proper connection, everything worked perfectly!

Took back cover panel off (upper) and removed the 4 1/4 inch nut screws. Used nut driver and removed the 4 screws holding control panel in place. Put new panel in place and unhooked electrical connections and installed on new panel. Plugged stove back in and checked operation. All OK, so then put back cover on and everybody is happy.

Cut 4 inch’s off the new terminal block wires then using my wire strippers stripped 1/2 inch off the ends , the old terminal block wires I stripped 1/2 inch at the ends using a wire nuts on both wires and electrical tape connected the terminal block to the stove plugged the new burner in and the burner worked 100%.

The rusted burner bowls were a given, simple remove and replace. The bake element was bad, meaning the loop was open (cracked). The element replacement should have been easier if I had read all of the feed back given on the reviews. The number one thing I must stress is that the stove needs to be powered down. Either via breaker or unplugged. I found out the hard way and had sparks flying all over the place. I figured that with the oven in the off position the element had no power, boy was I wrong! Don't ever assume that the appliance was designed for safety! I pulled out the stove and unplugged it, after that the replacement was very easy. One 1/4" nut driver was all that was needed.

The only hard thing was contorting my old beat up body and joints long enuff to reconnect the 2 wires and oven heat sensor and put in 6 screws with a 1/4" nut driver. I did remover the oven door and that made it much easier for me.

I had my husband fix it! Very easy for me.

It didn't take him long. The most difficult part was getting to the screws. He had to practically climb into the oven.

The parts were shipped promptly and the whole process was relatively painless!

I started with changing the bulb. I removed the small bracket that holds the glass cover over the bulb unscrewed the bulb and reversed to replace the bulb. To replace the control board I removed the top plate on the back of my stove took the small screw's out of the control panel and unplugged the wire's. Plugged the wire's into the right spots on the new control board and put it back together.