J710T3 General Electric Range - Instructions

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. I reattached them to the new element screwed it back in place and I was done. Could not have been easier! Getting the right replacement part the next day after placing the order was a pleasant surprise. This is the second time I used your company and I am very impressed with your service. I recommend you to everyone I can. Great Job!

Tried contacting GE and no luck, they did not have vintage parts. After searching and locating Partselect, I was able to see a pic of the actual replacement part. I wasn't sure about purchasing online (1st timer) but decided to go for it!

I was able to track the package, although FedEX was setup to deliver to my resdient, I had the package addressed to my office but we worked that out also and walla.

I was very please and now I can bake my famous Pot Roast again. The oven was not working for 8 mos.

Good Eaten!

SJ-Long Beach CA

Removed 2 mounting screws - Removed 2 screws used to attach wiring to element. Received new element and re-attached the 4 screws.

Turn off the breaker. Unscrew the element. Remove and replace with new element. Screw it back into place. Turn on the breaker.

That simple, that easy.

First I removed the two screws that hold the element in place. I then pulled the element out about 2 inches and disconnected the two wires.

I reconnected the two wires to the new element and screwed the new element to the wall of the oven where the element was held in place.

First removed screws then removed burned out element.Replaced with new element and replaced screws and cooked pizza.

It was realatively simple, turned off the power to the oven, removed the bake element , by loosening the two metal screws in the back of the oven, with a nut driver and removing the screws, then pulling the element outward, to expose the two wires ,that were connected to the element, using a nut driver to remove the two screws and a pair of pliers to hold the wire connectors, then removed the old element. Installed the new bake element, by connecting the two wires to the element, with the two screws, then pushing the element back in place , attaching the element to the back of the oven, with the two metal screws, finished with the installation, turned power back to the oven , and tested to make sure the oven worked , all done.

Repair was easy.
Note: the element leads have a potential across them,
so unplug the unit or you'll have an arc strike.

I liked the selection method at PartsSelect.com.
Finding the replacement part was easy from the pictures.
The prices were reasonable.

The part came next day, which was a surprise.
Removal and Installation was 4 screws.
I have become a DIY hero.

Only downside was going out for dinner every night ended.
This site is now a Favorite.

The delivery of the part was within 3 days.I only had to connect the two screws had biscuits that night.

I had to remove the door, burners, stove cooktop, both oven heating elements. Two j bolts in the rear of range hold oven box to range body and sandwich the seal in place. After removing the oven box the new seal could be installed, then reassemble everything.

The repair was a bit difficult because the screws connecting the wires to the element were small threaded bolts and no slot for a screw driver. They were very difficult to break loose - that's when we used the Liquid Wrench and waited. Other than that, the repair went smoothly. It is better to remove the oven door, if you can, otherwise the rear of the oven is not as accessible. It is also a good time to change the light bulb.

Simply removed the old one and replaced it with the new one. Part Select was the only company that was able to identify the part without the Model Number. The Model number was
worn off and unable to read. After going through several
on-line parts dealers, Part Select was the only company that could identify the part I needed. The repair was simple and
short. My old stand by oven is in operation again.
Thanks, Laura

I was a little leary of using a website to order a part to fix my oven, but we got the part within a week. It was very easy to install and it works like a charm!

It was so easy, we got on the General Electric web site and entered the old model number, found our match and ordered the part. It came 3 days later and it was so easy to remove the old one and install the new one, only two screws to remove. Saved a lot of money by doing it ourselves! Thank goodness for websites like this!!

I unplugged the stove, unscrewed two nuts, pulled the two wires forwrd and disconnected them. Attached the wires to the new burner and it works fine!