IF36INDFSF Dacor Refrigerator - Instructions

All Instructions for the IF36INDFSF
91 - 105 of 762

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
ice maker dripped water into ice bin, freeezing into large block of ice,
6 of 6 people found this instruction helpful.
  • charles from PHOENIX, AZ
  • Easy
  • 30 - 60 mins
  • Nutdriver
turn off water and unplug fridge. remove ice maker bottom mounting screw. just loosen the 2 top mounting screws. unplug wire harness from back of fridge. remove old icemaker from freezer compartment. once removed, salvage square endcover and reinstall on new maker. unfasten wire harness from old maker and reinsatll on new one. reinsert th ermal wire in new ice maker holding bracket. remove second wiring bracket and reinstall on new maker to hold remaining wires (not mentioned on "how to-" video). remove old ice maker on/off bale and reinstall on new one. remount new maker to top mounting screws, reinsert harness plug into fridge. replace bottom screw,
Was this helpful?
Thank you for voting!
I accidentally damaged the power cord
7 of 9 people found this instruction helpful.
  • Rob from Kalamazoo, MI
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
The other guy described it perfectly so all I can add is that this repair was as simple as they come. Don't hesitate.
Was this helpful?
Thank you for voting!
My icemaker started leaking water into the catch basin and turning my ice into one big ice burg.
6 of 7 people found this instruction helpful.
  • gary from carleton, MI
  • Really Easy
  • Less than 15 mins
  • Nutdriver
Well folks I put up with an ice burg all summer when I really should have took the time to fix it. You know how it goes though. You get so busy you just put it off.
Well don't put this one off because this is just how easy it went.
I came home one evening and wanted to make a drink to relax but that big glob of ice was there w aiting for me. I took a crewdriver and beat it down so I could pull the catch basin out. Having looked it over for a minute I grabed a nut driver and took three of the screws out that held it in. I unpluged the wire and bingo it was out. Maybe five min. had elasped.
After taking the unit out I notice how the non stick surface was coming off of the tray and that explains the black pieces that were getting into my ice.
Getting the model number off the back of the fridge and writing it down I went to my trusty lap top and did a quick search for a ice maker for my Jenn Air refrigeraton and blamo...! Part Select came up and I put the part number in their search engine and bingo again there it was, my part.
One quick order and in three days it was right there by my door when I got home.
Now i'm so excited. I went into the house and didn't even chage out of my dress clothes. Within five minutes it was in. Now I just had to wait for the timer to do it's thing and sure enough, I awoke the next morning to a whole tray of beautiful ice cubes. Wow no more ice burgs.
The moral of my story is I spent so much time hacking out that glob of ice and for fifteen minutes of my time, I could have been siping on cold ones by the pool but now old man winter is pressing down on me and I guess a lesson learned was a lesson earned. Fix it!
Was this helpful?
Thank you for voting!
No ice
8 of 13 people found this instruction helpful.
  • Jon from Boise, ID
  • Really Easy
  • Less than 15 mins
  • Nutdriver, Screw drivers
1 screw remove assembly. Unplug cable harness and remove old cover and wire arm. Replace cover and wire arm and attach wire harness on assembly end. Re attach using screw removed in first step. Plug in wire harness. Making ice within 30 minutes.
Was this helpful?
Thank you for voting!
All three lights are not working...lights are off but refrigerator still cooling. Also, the control box not lit up to show the temparture for freezer and refrigerator
7 of 10 people found this instruction helpful.
  • Antonio from San Antonio, TX
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Used a screw driver to pull old switch. Pulled one wire at a time, only two wires. After wires instlled to new switch push new one back in place where the old one was.
Was this helpful?
Thank you for voting!
chef drawer cover
6 of 7 people found this instruction helpful.
  • Maria from Cream Ridge, NJ
  • Really Easy
  • Less than 15 mins
take the old one out replace with new once - no instructions required, no tools needed
Was this helpful?
Thank you for voting!
broken front wheel
7 of 10 people found this instruction helpful.
  • Robert from Orting, WA
  • Difficult
  • Less than 15 mins
  • Nutdriver, Pliers
remove front grill. with pry bar and wooden block, elevate side with broken wheel and insert wooden block behind assemble from the exterior bottom. With roller wheel assemble lose from the wooden block remove front elevator screw from the front frame. next remove cotter pin with the pliers and pull assemble pin. next elevate assemble out. drill out axle on the crimp side insert from the hardware store one 5/16 x 21/2 bolt with nut and new wheel. reinsert assemble in the reverse order. Remove wooden block and adjust height of wheel. replace grill. job complete. good job
Was this helpful?
Thank you for voting!
Broken glass on pantry door
6 of 7 people found this instruction helpful.
  • Michael from Roseville, MI
  • Really Easy
  • Less than 15 mins
Pulled the broken pantry door off, and snapped the new door in place. Vry simple.
Was this helpful?
Thank you for voting!
The Switch Broke...Absolutely Fell Apart.
5 of 5 people found this instruction helpful.
  • Duncan from Metairie, LA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
I simply removed the old switch using 2 small screwdrivers and the old switch case popped out. I then upluged the wires from the old switch and reversed the process. Didn't take longer than 5 minutes begining to end! Thank you for the great service! Duncan quaid
Was this helpful?
Thank you for voting!
Noisy damper
5 of 5 people found this instruction helpful.
  • Keith from OLYMPIA, WA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Easy fix, it's right in the back of the fridge under a cover that just clips in, a piece of foam, and two screws. The hardest part is getting the clips free without breaking them. After replacement it's silent instead of making a grinding noise regularly.
Was this helpful?
Thank you for voting!
Control noisy when opening and closing removed damper housing
5 of 5 people found this instruction helpful.
  • Nelson from CATSKILL, NY
  • Easy
  • Less than 15 mins
  • Screw drivers
Pop off vent cover remove 2 screws removed cover housing and foam. Removed damper by unclipping tabs on left and right side of control lift up and out. Unplugged power wires reinstalled in reverse order.
Was this helpful?
Thank you for voting!
Top section warm, but freezer okay.
5 of 5 people found this instruction helpful.
  • Christopher from HOMESTEAD, FL
  • Easy
  • 15 - 30 mins
  • Screw drivers
Popped off the control panel at the top behind the door. Found the thermistor and replaced it, cutting the wires and splicing the new one in. Immediately the warm section of the refrigerator was getting below freezing temperature readings, so the cooling vent was not opening. I put the old one back on and the temperature readings went back to being accurate. So this was not the problem. I believe now that the fan somehow is not blowing enough cold air up. So now I'll probably buy a fan motor and maybe a blade and try that. Otherwise the computer module I priced at $500 so I hope it isn't that. I replace the fan motor a few years ago already.
Was this helpful?
Thank you for voting!
The ice maker stopped making ice.
5 of 5 people found this instruction helpful.
  • Thomas from Cupertino, CA
  • Easy
  • 15 - 30 mins
  • Nutdriver
I did a few tests with the old ice maker and determined that it was the ice maker itself that was faulty. The replacement part I ordered exceeded my expectations in the time it took to get the part. I reused the arm, wire harness and clamps from the old icemaker. Then it was a simple install into the bottom freezer compartment, turning on the water supply and bingo...lots of ice cubes.
Was this helpful?
Thank you for voting!
Fresh Food Compartment occasionally going down to 28-30 degrees F
5 of 5 people found this instruction helpful.
  • Galen from WASECA, MN
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Failure detected as Damper Control at upper rear of compartment would continuously open/close, would never stay open or closed. Sometimes the main board would turn it off (maybe a low thermistor limit?), but it would stick open a bit, and keeping letting freezer air into fridge. Could have potentially been control board, but as it turns out after disassembly of the defective damper, the internal microswitch was stuck in the closed position so it wouldn't shut off the motor. Easy fix by gently pulling the cover off the damper control, pull out Styrofoam encasement, then a phillips to remove the damper assembly. Gently push tabs to release wire connectors. Reverse the process and you're done! If I really wanted to go on the cheap, I could have just changed the microswitch, but that looked like a shaky maneuver at best. This site saved me on this one, so happy to share my experience with this Maytag and its nasty habit of freezing my milk and eggs!! :)
Was this helpful?
Thank you for voting!
Icemaker would not fill with water.
7 of 11 people found this instruction helpful.
  • Linford from Cedarville, NJ
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Removed screw under ice maker. Tilted ice maker up to remove unit from upper two screws. Disconnected plug at rear of freezer. Attached wiring harness, baler arm and cover from old to new ice maker. Reinstalled in reverse order. Had ice within one hour. Very easy fix.
Was this helpful?
Thank you for voting!
All Instructions for the IF36INDFSF
91 - 105 of 762