- Home
- IF36INDFSF
- Instructions
IF36INDFSF Dacor Refrigerator - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Thought motor was bad freezer cold fridge hot
4 of 4 people
found this instruction helpful.
-
Wayne from PENNINGTON, NJ
- Really Easy
- 30 - 60 mins
Ordered new fan motor
Got part took fridge apart
Result was the motor was running
The fan blade had come off the motor
Replaced the motor anyway and reinstalled the fan, working well
Got part took fridge apart
Result was the motor was running
The fan blade had come off the motor
Replaced the motor anyway and reinstalled the fan, working well
Was this helpful?
Thank you for voting!
Frost on the edges of the freezer and all around the freezer door
4 of 4 people
found this instruction helpful.
-
Robert from EVERETT, WA
- Really Easy
- 30 - 60 mins
-
Screw drivers
I was getting small sections of ice and a snow like build - up around the freezer door. I thought that the door was not sealing tight enough and that the cold air was leaking out. The original door gasket appeared to not have any flexibility anymore and was getting hard. I ordered a new door gasket from PartsSelect. When the gasket arrive
... Read more
d it was in a large enough box and that saved me some time as the gasket was not "crushed" to the point where there were a lot of kinks in the gasket. I used a hair dryer on low to warm the gasket and stretch it out some. The freezer door required me loosening four small screws and lifting the door off. I placed the door on an old blanket so not to scratch the finish. It was easy to remove the old gasket and after doing so I cleaned the track where the new gasket was to go with isopropyl alcohol, Once cleaned, I placed the gasket over the channel in the door where the old gasket had been and started installing the new gasket. I started at the corners and you can feel the gasket snap into place. Once the four corners were done I started at the top and installed the gasket the rest of the way. You can feel it snap into place. as you work your way around the gasket channel. Once the gasket was in place I placed the door on the four small grooves where the door had been and tightened up the screws. I made sure that no white from the inside of the freezer door was showing after the gasket was in place and that the gasket had some "spring" to it. The door was back on, the gasket was tight and it appeared to be a good seal. Around 12 hours later I checked the freezer and there was no more ice or "snow" on the edges of the freezer. While the gasket was not inexpensive, it is a genuine OEM piece, and the gasket is a lot cheaper than a new refrigerator!
I hope this was helpful...
I hope this was helpful...
Read less
Was this helpful?
Thank you for voting!
Water Fill Cup Broke
5 of 7 people
found this instruction helpful.
-
Sam from Las Vegas, NV
- A Bit Difficult
- 30 - 60 mins
-
Screw drivers
The Ice maker unit had to be removed and the shaft had to also be removed, which required dis-assembling the motor drive. The thickness of the shaft and the bearing fill cup prevents it from simply pushing it in place. Other than that I have Ice.
Was this helpful?
Thank you for voting!
Plastic axle piece breaks off on left side of door to slide out drawer under crispers
6 of 10 people
found this instruction helpful.
-
Robert from Randolph, NJ
- Really Easy
- 15 - 30 mins
-
Screw drivers, Socket set
Remove crispers & bottom drawer. Removed glass piece. Unscrewed piece( small nuts not screw heads) There is also a nubbie at front. You must remove by sliding out & lifting back of part. Reuse screws to replace piece & drawer runner. It took 15 to 20 minutes. I am all thumbs. If I can do anyone can do!
Other Parts Used:
Was this helpful?
Thank you for voting!
Refrigerator light would not stay on
4 of 4 people
found this instruction helpful.
-
Dave from Manchester Center, VT
- Easy
- 15 - 30 mins
-
Nutdriver, Socket set
Removed the 2 screws holding the light bulb shield, then the 4 uolding the metal panel. Unplugged the olw door switch and replaced.
reassembled the pieces.
reassembled the pieces.
Was this helpful?
Thank you for voting!
Broken Left End Cap
4 of 4 people
found this instruction helpful.
-
Jeffrey from San Clemente,, CA
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
The peg on the door broke off the left end cap. This seems to be a bad design on the part of amana. It's happened twice now. Very fragile. The repair was so easy that my wife tackled it while I was at work because I was too busy to do it. She said the only problem was removing all the trays, shelves, and drawers out of the fri
... Read more
dge and putting that back together which is a bit cumbersome and tricky. The actual part removal and replacement is straight forward once the other stuff is removed to get to the screws that are holding the end cap on. When I did it for the right end cap it was a bit more challenging because there were more parts that had to come off and go back on. I am happy that this can be easily repaired, but not happy with amana that the sliding drawer and door are so susceptible to breakage at the two pegs. This is a flaw in the design.
Read less
Was this helpful?
Thank you for voting!
broken roller
4 of 4 people
found this instruction helpful.
-
John from Capac, MI
- Really Easy
- 15 - 30 mins
-
Nutdriver
proped up frig, loosened screws, cut pin, installed rooler w/ new pin, rounded pin end, reistalled, lowered frig...everyone happy, thanks again partselect.
Other Parts Used:
Was this helpful?
Thank you for voting!
Water overflowing ice maker
5 of 8 people
found this instruction helpful.
-
James from Denver, NC
- Really Easy
- Less than 15 mins
-
Nutdriver
Removed the 3 screws that hold the ice maker in place and remove the cover and level wire. Put the cover and wire on new part and install the 3 screws. Had ice within 1 hour. A very easy job for the do it yourselfer. Suspect the heat coil that melts the cubes was not working in the old unit and cubes stayed in the tray.
Was this helpful?
Thank you for voting!
chef's pantry lid was cracked
4 of 5 people
found this instruction helpful.
-
Darrell from Yakima, WA
- Really Easy
- Less than 15 mins
A jar was dropped on the chef's pantry lid and cracked the lid. I unhinged one side of the lid from the pantry drawer by gently pushing outward on one of the hinge pins. The lid slid out easily. I then reversed the process using the new lid and it went in smoothly. Be sure to align the lid so it rests on the shoulder of the pantry drawer.
... Read more
Simple task, no tools, and less than 5 minutes effort. The replacement part was perfect.
Read less
Was this helpful?
Thank you for voting!
Old one leaks on one side
4 of 5 people
found this instruction helpful.
-
Orlando from Bayonne, NJ
- Very Easy
- Less than 15 mins
Simply cut the water tube on both sides of connector and push in the new one.
Was this helpful?
Thank you for voting!
One of the light bulbs went out on my Whirlpool refrigerator.
4 of 5 people
found this instruction helpful.
-
Brian from LAKE CHARLES, LA
- Very Easy
- Less than 15 mins
-
Screw drivers
I changed the bulb but it still didn’t work. I ordered a bulb holder and replaced it and it works properly now. It was an easy repair, remove the bulb, gently pry the bulb holder out with a screwdriver and snap the new one in.
It was useful that under the description of the part in the catalog, it showed that this part was oft ... Read more en used to repair this issue. The service was great and the delivery was fast.
It was useful that under the description of the part in the catalog, it showed that this part was oft ... Read more en used to repair this issue. The service was great and the delivery was fast.
Read less
Was this helpful?
Thank you for voting!
The fill tube was freezing up after about 60 days of use.
4 of 5 people
found this instruction helpful.
-
John from CORNELIUS, NC
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Pulled the unit from the wall, and unplugged, and turned off the water. Removed the back plate at the bottom of the refrigerator to gain access to the water inlet valve. Disconnected three tubes and two electrical connections and reconnected to the new inlet valve. Reassembled the back plate. Then turned everything back on and checked f
... Read more
or leaks. Re-Installed the back plate. This was a fairly easy repair. The only problem I had was getting the water lines off the old valve. It was a bit of a struggle for me. I did watch a couple of you tube videos before I got started.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Broken light switch
4 of 5 people
found this instruction helpful.
-
Terry from WARMINSTER, PA
- Really Easy
- 15 - 30 mins
-
Screw drivers
Watched video. Unplugged refrigerator and popped out switch. In plugged connector and pushed switch in place. Plugged in refrigerator and the light worked
Was this helpful?
Thank you for voting!
leaking ice maker,big chunks ot ice were forming and had to remove them 2-3 times a day
4 of 5 people
found this instruction helpful.
-
Linda from Johnson City, NY
- Really Easy
- 30 - 60 mins
-
Screw drivers
removed old ice maker by taking out a couple of screws in the back of freezer,when new ice maker arrived i saw that it didn't have the same hose apparatus as old one so I easily took apart old one then took apart new one and switched them out-very-- easily done for a 61 yr old lady I might add-- also had to reinstall ice maker arm off old
... Read more
ice maker as new one does not come with one Then installed new ice maker in freezer I am very very pleased,sure saved a lot of money doing it my self
Read less
Was this helpful?
Thank you for voting!
FREEZER WOULD NOT DEFROST.
4 of 5 people
found this instruction helpful.
-
JEFF from SEATTLE, WA
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
I initially tested the heating element and defrost thermostat using an ohm meter. the defrost thermostat was incased in ice, so I replaced it first. The refridgerator worked for about a week and then froze up again. I then replaced the thermistor and the unit is working as designed.
Was this helpful?
Thank you for voting!