- Home
- IF36INDFSF
- Instructions
IF36INDFSF Dacor Refrigerator - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Compressor would not start
7 of 7 people
found this instruction helpful.
-
Rich from Monon, IN
- Really Easy
- Less than 15 mins
-
Nutdriver
Removed back access cover with quarter inch nut driver, unplugged wire harness, pulled old relay out & plugged in new one, reconnected wire harness, and reinstalled access cover. Piece of cake. (Shipping was very quick) ***Frig was only 3yr an 1 mounth old.*** Maytag - Dependable Huh?
Was this helpful?
Thank you for voting!
Not freezing or keeping thing cold in fridge
8 of 10 people
found this instruction helpful.
-
BRUCE from AMMON, ID
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
Once I got the right part the repair was quick and easy. All I had to do is get the old part off with a screwdriver and curved needle nose pliers and the old part came right off. The new part went in just as easy. Quick and easy. Less than 15 minutes.
Was this helpful?
Thank you for voting!
broken light switch in the freezer
7 of 7 people
found this instruction helpful.
-
kathleen from GREEN VALLEY, AZ
- Easy
- Less than 15 mins
-
Screw drivers
We removed the old switch, unplugged it, plugged the new one in and it was easy to do. But when we tried to put the switch back in we had a very hard time doing it. Eventually got it in, but if it had not been for the difficulty we had getting the new switch to snap in to place, it would have taken under 5 minutes.
Was this helpful?
Thank you for voting!
no water when under sink water filter installed
11 of 19 people
found this instruction helpful.
-
Emi from Arlington, VA
- Easy
- Less than 15 mins
I called the installer of my filter unit and he told me that often, thhe fridge filter is the problem. Like magic it worked
Was this helpful?
Thank you for voting!
Power surge cause compressor to stop functioning
7 of 7 people
found this instruction helpful.
-
Alvin from ORANGE PARK, FL
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers, Socket set
Followed the YouTube video linked to the Compressor Start Device and Capacitor I purchased. The repair was just as easy as the technician in the video said it would be. Removed the back panel, remove the clamp, worked the Compressor Start Device and Capacitor off the electrical prongs and replace it with the new one. After I reassemble
... Read more
the refrigerator, it was fully operational. Very easy to do and only required a few tools.
Read less
Was this helpful?
Thank you for voting!
The plastic wheel broke in half at the right front of the refrigerator.
7 of 8 people
found this instruction helpful.
-
Ralph from Camillus, NY
- A Bit Difficult
- 30 - 60 mins
-
Pliers, Screw drivers, Socket set
The good news is that the part (the wheel was available.) I bought two in the event that the other wheel may break in the future. The bad news is that the housing that holds the wheel was riveted together by the wheel axle. It would have been nice to know that before I bought the part and if the housing with the wheel installed was ava
... Read more
ilable. The refrigerator was at my summer house a hundred miles away. Anyway, we had to grind the end of the riveted axle to dislodge it from the wheel housing. With the axle dislodged from the housing we were able to install the wheel and then hammer the end of the axle flat to keep in place, like the original rivet installation. It is not perfect but it held and should be fine. I am glad I was able to get the part and will be back in the future, if in need of other parts.
Read less
Was this helpful?
Thank you for voting!
Broken Piece
7 of 8 people
found this instruction helpful.
-
anthony from georgetown, IL
- A Bit Difficult
- 30 - 60 mins
-
Screw drivers
Had to disassemble ice maker to install part. . .
Was this helpful?
Thank you for voting!
light not working in fridge
7 of 8 people
found this instruction helpful.
-
Michael from East Meadow, NY
- Really Easy
- Less than 15 mins
-
Screw drivers
It was so easy!
Thanks for the rush to my home on the part.
I just unscrewed the plate that locks in the light switch (screwdriver) and unplugged the old faulty part and plugged in the new switch, screwed the cover back on and I was done!
Easy!
And I am not Mr. Fix-it!
Thanks for the rush to my home on the part.
I just unscrewed the plate that locks in the light switch (screwdriver) and unplugged the old faulty part and plugged in the new switch, screwed the cover back on and I was done!
Easy!
And I am not Mr. Fix-it!
Was this helpful?
Thank you for voting!
Lid kept popping off Pantry drawer
7 of 8 people
found this instruction helpful.
-
Alice from Santa Ana, CA
- Really Easy
- Less than 15 mins
Could not figure out why this was happening suddenly. Then remembered I had recently changed the lid to one I had stored for over two years in the garage. They had sent me a replacement lid when the unit was less than a year old because the origianl had a crack in the clear section. Noticed it seemed a little warped. Thought I would
... Read more
replace it to see if that solved the
problem.
We had to replace the side panel of the draawer because the warped lid had broken the peg off of one side. I didn't want that to happen again.
The new lid did the job....This company is the only one I will use in the future for my appliances. Very easy to find parts and the pricing was better.
problem.
We had to replace the side panel of the draawer because the warped lid had broken the peg off of one side. I didn't want that to happen again.
The new lid did the job....This company is the only one I will use in the future for my appliances. Very easy to find parts and the pricing was better.
Read less
Was this helpful?
Thank you for voting!
ice maker dripped water into ice bin, freeezing into large block of ice,
6 of 6 people
found this instruction helpful.
-
charles from PHOENIX, AZ
- Easy
- 30 - 60 mins
-
Nutdriver
turn off water and unplug fridge. remove ice maker bottom mounting screw. just loosen the 2 top mounting screws. unplug wire harness from back of fridge. remove old icemaker from freezer compartment. once removed, salvage square endcover and reinstall on new maker. unfasten wire harness from old maker and reinsatll on new one. reinsert th
... Read more
ermal wire in new ice maker holding bracket. remove second wiring bracket and reinstall on new maker to hold remaining wires (not mentioned on "how to-" video). remove old ice maker on/off bale and reinstall on new one. remount new maker to top mounting screws, reinsert harness plug into fridge. replace bottom screw,
Read less
Was this helpful?
Thank you for voting!
Freezer temperature goes down to -20*F before compressor stops but refrigerator side remains normal 38*F and compressor makes a grunting noise while running.
6 of 6 people
found this instruction helpful.
-
Aquilino O from VALLEJO, CA
- Easy
- 1- 2 hours
-
Nutdriver, Screw drivers
Unplug ref then remove lower(freezer) panel plus trays and thermistor’s cover/holder then remove the evaps cover. I found the evaps all frozen up. Cut and remove old thermistor, strip wires 1/2 inch then cut the new thermistor wires to length and strip 1/2 inch, use the enclosed insulated crimp type connector and put back everything in t
... Read more
he reverse order. It works great afterwards.
Read less
Was this helpful?
Thank you for voting!
Button holding snack drawer cover was broken
6 of 6 people
found this instruction helpful.
-
Claude from Phoenix, AZ
- Really Easy
- Less than 15 mins
-
Screw drivers, Socket set
1. removed both bottom crisper drawers
2. removed glass shelf under crisper drawers
3. removed shelf support pieces
4. removeded snack drawer
5. removed left slide rail using phillips screwdriver (2 screws)
6. removed LH end cap using socket wrench (3 screws)
7. attached new LH end cap
8. attached slide ... Read more rail
9. installed glas shelf supports
10. installed glas shelf
11. install bottom crisper drawers
12. install snack drawer
13. install snack drawer top
total time was less than 15 minutes
2. removed glass shelf under crisper drawers
3. removed shelf support pieces
4. removeded snack drawer
5. removed left slide rail using phillips screwdriver (2 screws)
6. removed LH end cap using socket wrench (3 screws)
7. attached new LH end cap
8. attached slide ... Read more rail
9. installed glas shelf supports
10. installed glas shelf
11. install bottom crisper drawers
12. install snack drawer
13. install snack drawer top
total time was less than 15 minutes
Read less
Was this helpful?
Thank you for voting!
Replace crisper drawer
7 of 9 people
found this instruction helpful.
-
Eric from Stanardsville, VA
- Really Easy
- Less than 15 mins
The front had to be removed from old drawer a put on new one
Was this helpful?
Thank you for voting!
Glides easy to install, about 15 minutes
9 of 15 people
found this instruction helpful.
-
Mary Sue from Tinley Park, IL
- Easy
- Less than 15 mins
-
Screw drivers
you need to take the deli drawer out, make sure your flat head screw driver is large enough for the head of the screw as screwing into the plastic is a bit difficult. Other than that there are 2 screws and its pretty easy.
Was this helpful?
Thank you for voting!
Insulation was disintegrating.
6 of 6 people
found this instruction helpful.
-
Julie from San Diego, CA
- Really Easy
- 15 - 30 mins
-
Screw drivers
On the back of the refrigerator, I unscrewed and removed the lower-right panel. As I peeled the insulation off the panel, the insulation would disintegrate, so I used a vacuum-cleaner hose to remove most of the insulation. I removed the remaining adhesive with my fingers. I peeled the backing off the new insulation, and stuck it to the pa
... Read more
nel.
I had ordered two pieces of insulation, hoping to also replace the insulation behind the compressor, but removing the compressor was complicated and risky, so I returned the second piece of insulation.
I had ordered two pieces of insulation, hoping to also replace the insulation behind the compressor, but removing the compressor was complicated and risky, so I returned the second piece of insulation.
Read less
Was this helpful?
Thank you for voting!