Models > HTDX100EM8WW > Instructions

HTDX100EM8WW Hotpoint Dryer - Instructions

All Instructions for the HTDX100EM8WW
61 - 75 of 270
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Dishwasher would not start
Removed panel to access the interlock switches. There were two. The button on one switch was fine and the button on the other would not depress. Ran a continuity test and it failed. The switch also had a burnt smell
Parts Used:
Interlock Switch
  • Dameon from SMYRNA, DE
  • Difficulty Level:
    Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Pliers, Screw drivers, Socket set
4 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
dishwasher did not start
Took out interlock switch (two leads) and replaced with new one. As simple as that.
Parts Used:
Interlock Switch
  • Lawrence from ROLESVILLE, NC
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
7 of 13 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Catching clothing and reping
Removed that to screws for that top first and door shake top little to that front and I took two screws on that top each side and removed that front and lint trap and install the new
Parts Used:
Dryer Lint Chute Assembly
  • Jose from LILBURN, GA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
4 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broke switch and later on the black piece on motor timer.
Unplug dryer, remove screws and panel. Take picture of dryer motor so you will put wires back the same way . Remove screws using Allen wrench, then unplug wires put the new motor on secure, then put wires back on. View the photo make sure the wires are the same. Then plug your dryer back up. And Happy drying..
Parts Used:
Push-to-Start Switch Timer Knob
  • Lear from SMYRNA, TN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
4 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Timer controller knob broke off and did not leave enough center pole to attach new knob.
Pulled dryer out from wall and used screwdriver to remove back plate and screw holding timer controller. Once loose I then held new part next to old part and switched wires one at a time, afterwards I replaced back and pushed dryer back into position.
Parts Used:
Dryer Timer Timer Knob
  • Amy from OGDEN, UT
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
belt was broken.
remove top of cabinet and front panel. placed belt around drum and replaced idler pully placed new belt around pully and was done. not a hard job at all. replced front panel and top. thanks to a speedy delivery of my parts dryer was only down two days.
Parts Used:
PULLEY Drive Belt
  • robert from phenix city, AL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Wrench (Adjustable)
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Very noisy operation
Very easy! Removed old parts, and installed new parts in reverse order. Dryer was running, and sounded like a new appliance in 35 minutes!
Parts Used:
TOP BEARING Dryer Lint Chute Assembly Duct Felt Seal Drum Glide Bearing - White (Sold individually) DRYER BEARING SLIDE 2-PACK
  • Larry from LAS VEGAS, NV
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
4 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
timer knob and on/off knobs split at base, not engaging
Popped off old knobs, popped in new. Sorry, nothin' to it or I would'a yelled HELP!
Parts Used:
Knob and Clip Timer Knob
  • Karen from THIBODAUX, LA
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
lint filter was broken
remove the broken one and replace it with the new one
Parts Used:
Lint Filter - White Frame
  • walter from STRATFORD, CT
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Knob and clip both broken
I just removed old parts And put the new part on it was very easy to do.
Parts Used:
Knob and Clip
  • Sharon from LAKE CITY, SC
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Knob kept turning around without clicking
Husband took off the back of dryer and took off old timer and replaced it with the new, put on new knob, worked great, Ordered it on day, and we received it the next day, thank you for the quick delivery.
Parts Used:
Dryer Timer Timer Knob
  • Susan from Latham, OH
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers, Screw drivers
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dryer Timer not functioning
Followed the directions but met resistance when the
timer could not be slipped off the "peg".
This timer was installed with a very small screw to remove
and install the new timer.- Thus, called an electrician
who had the very small screw driver to install the timer!
So $$$$$$$$$$. unhappy about this!
Parts Used:
Dryer Timer
  • Gretchen from SPRINGFIELD, IL
  • Difficulty Level:
    Very Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
no problem
this was a part i ordered for future use. i was very happy with the ordering process and speed of delivery from PartSelect.
Parts Used:
Lint Filter - White Frame
  • john from west milford, NJ
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
remove plastic and insert
inserted the lint catcher into the opening to replace the old one
Parts Used:
Lint Filter - White Frame
  • MARY from ERIE, PA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dryer belt was broken
I removed the top cover and the back cover to install new belt.
Once i put new belt i discovered that the pulley was also broken so now i have order the pulley so that i can complete the repair
Parts Used:
Drive Belt
  • Alvino from newtown, CT
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Screw drivers
4 of 8 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the HTDX100EM8WW
61 - 75 of 270
Back to Top