All Installation Instructions for General Electric Dryer GTMX180ED6WW

Broken water filter appliance

Literally turned off the water to the refrigerator, disconnected the lines from the back and took one screw loose from the inside of the unit. Slid out old filter connection and slid in the new one and did reverse process.

Parts Used:

FILTER MANIFOLD

William from BLUE RIDGE, GA
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

7 of 8 people found this instruction helpful.

Was this instruction helpful to you?

Freezer not getting cold enough to freeze ice cream

I took the advice off of your website about the only thing that will fix
the problem is change the run capacitor. I felt assured that I would
have a working refrigerator freezer after making this change. I was
pretty disheartened when it didn`t solve anything. I was not going to
take the new part back out after the small challenge of putting it in.
The next day I found out how to test the old capacitor and it was still
good. I will just have to eat the $49. I did learn not to take advice from
a website even if it seems like a sure thing

Parts Used:

Run Capacitor

Gary from ROSETO, PA
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

7 of 9 people found this instruction helpful.

Was this instruction helpful to you?

Broken Door Handle

Clips on the inside of the door handle had snapped off, 1 minute later it worked like new. NO TOOLS required! So happy my older appliances can have new life by the parts carried by PartSelect. Thanks!

Parts Used:

Door Handle - White

Cheryl from Old Town, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

8 of 12 people found this instruction helpful.

Was this instruction helpful to you?

broken dryer handle

My husband broke the door handle, but of course, i had to be the one to order the part & fix it. I ordered the part on the weekend and much to my suprise it was on my doorstep on Tuesday when I got home from work. Then I saw the part was shipped from nearby Louisville. I was overly happy with partselect!!!!! All I did was open the packaging and clip the dryer handle into the 4 holes. Easy as pie!!!!

Parts Used:

Door Handle - White

Angela from Richmond, KY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

6 of 7 people found this instruction helpful.

Was this instruction helpful to you?

Dishwasher wouldn’t start

Took the screws out of the back of the doorl located the switch and replaced it put screws back in and it was fixed

Parts Used:

Interlock Switch

Stephen from MARENGO, OH
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

7 of 10 people found this instruction helpful.

Was this instruction helpful to you?

The Front Drum Glides wore out

I first unplugged the unit, opened the top, disconnected and took off the control panel, took off the front panel to determine the source of the squeaking noise coming from the Dryer. I saw that 3 of the 4 Front Drum Glides were gone and the drum had worn away significant amounts of plastic from the Top Bearing Assembly. I purchased the Top Bearing Assembly and a set of 4 Front Drum Glides. Disassembled the damaged parts and reassembled with the new replacement parts. The reassembly took less than 20 minutes. I plugged in the Dryer and viola! It works as good as new.

Parts Used:

DRYER FRONT BEARING WHITE 2PK

Al from Elmhurst, IL
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

6 of 7 people found this instruction helpful.

Was this instruction helpful to you?

Dryer would not tumble the clothes.

After finding the belt was broken, I also discovered the idler pulley was broke. Your website made it incredibly easy to identify and purchase the parts. This is my third great experience with your site. The last repair was the whole front bearing assembly and that went very smooth thanks to your site. Keep up the great work and thanks again.

Parts Used:

Idler Pulley Wheel

Drive Belt

David from Gibraltar, MI
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

10 of 19 people found this instruction helpful.

Was this instruction helpful to you?

Dishwasher would not start

Removed panel to access the interlock switches. There were two. The button on one switch was fine and the button on the other would not depress. Ran a continuity test and it failed. The switch also had a burnt smell

Parts Used:

Interlock Switch

Dameon from SMYRNA, DE
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Pliers, Screw drivers, Socket set

6 of 7 people found this instruction helpful.

Was this instruction helpful to you?

Plastic housing for the door latch mounted in the chassis of the dryer was damaged so the section of the latch in the door wouldn't align.

This kept the interlock open and shut off the dryer when the door swung open The broken latch was popped out using a flat blade screwdriver and the replacement snapped into place by hand. Good as new!

Parts Used:

Door Latch

STAN from UPPER ARLNGTN, OH
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

5 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Refrigerator to warm

Instructions say run capacitor is by motor, but on this frige its in the refrigerator compartment. The capacitors looks different, one square and the other long

Parts Used:

Run Capacitor

Lloyd from PITTSBURG, CA
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

5 of 5 people found this instruction helpful.

Was this instruction helpful to you?

The dryer drum wasn't spinning, but I could hear the motor and feel the heat from the heating element.

UNPLUG the dryer. I removed the top panel by removing the two screws at the top of the dryer door. There are some hooks toward the back of the top panel, so you'll need to slide it to the left to get it off. The front panel needs to be removed by removing two screws just inside the top left and right corners. Lift and set it aside. I didn't disconnect the door wiring, but you can if you need to do so. I just spun the front panel to the left and out of the way. With the drum exposed, I confirmed the belt was broken. I replaced the belt, then the front panel and top panel. While I was inside the dryer, I did a through cleaning with the vacuum to get all the lint.

The video on the site is easy to understand and a snap to follow.

Parts Used:

Drive Belt

David from LAWRENCEVILLE, GA
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

5 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Replaced Drum Bearing Front And Rear

Pulled the unit all apart to replace the rear drum bearing. Also replaced the front bearing. Works like brand new. Easier then I thought

Parts Used:

DRYER FRONT BEARING WHITE 2PK

philip from pickens, SC
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Screw drivers, Socket set

5 of 6 people found this instruction helpful.

Was this instruction helpful to you?

dishwasher did not start

Took out interlock switch (two leads) and replaced with new one. As simple as that.

Parts Used:

Interlock Switch

Lawrence from ROLESVILLE, NC
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

7 of 13 people found this instruction helpful.

Was this instruction helpful to you?

Interior light would not come on when right hand door was open

Remove the screws from the two door pivot covers. Remove the covers and set aside. Remove the screws from the control board; disconnect the electrical connections; remove the door light switch, install door light switch then reinstall everything.

Parts Used: