GT15B2F3EV Admiral Refrigerator - Instructions

Samuel from HUDSON, NC
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Door Shelf Retainer Bar Replacement.

The firt hard thing was waiting for the part to arrive, but that went quick. The second hardest part was opening the box. Shucks I got a paper cut, should have used a razor but while wife wont let me have sharp objects. Oh, yeah I had to find the hachsaw. I fooled everyone I knew where that was too. Be sure to measure properly, because if you cut too short then you have to stretch the bar. I havn't found any type of bar stretcher that works. It's best if you clamp the metal bar to a 2 X 4 piece of wood in order to steady the metal bar while you cut. You can't cut to well trying to hold the metal bar in your hand. The best part was completeing the job by installing the bars. Finally I have more room in my freezer to store food in the doors. This is my story and I am sticking to it. Have fun.

Parts Used:

DARYL from MANDEVILLE, LA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

2 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Light rocker switch broke and refrigerator light couldn't go on.

I just popped out the old switch with a flat head screwdriver. Removed the connections and then installed new switch by reversing steps. Popped in back in and the light went on.

Parts Used:

Cathy from HOPATCONG, NJ
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

2 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Brackets holding retainer bar on botton door shelf had broken.

Used screwdriver & pliers to remove old brackets. Installed retainer on new brackets and snapped them into place in the refrigerator door.

Parts Used:

Edward from METAIRIE, LA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

The ice stripper cracked from freezing.

There was three screws to remove to unmout the ice maker, and unplug the wire harness,then two to remove to slip in new stripper. All took about 20 mins.

Parts Used:

Refrigerator Ice Stripper

David from Discovery Bay, CA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver

3 of 8 people found this instruction helpful.

Was this instruction helpful to you?

Rocker on switch broke off

Eased the putty knife under the edge of the switch housing and pried it off. Pulled two wires off the old terminals and hooked them onto the new one and reinstalled into the refrigerator body.

Parts Used:

David Barnes from ROSWELL, NM
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Light switch broke off

We looked up the problem online with the model number of the refrigerator. We ordered the part and followed the video installation that was sent with the order and was found online prior to purchasing

Parts Used:

Kathy from TEMECULA, CA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Broken door shelf retainer

removed broken retainer with pliers and inserted new part. It was extremely easy---and I have ZERO mechanical skills.

Parts Used:

Jane from Albuquerque, NM
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

light did not work on the refrigerator side

bulbs were not burnt out. received the new switch in a few days. watch the short video, was good to see how it comes out. used a putty knife to release the defective switch, removed wires put them on the new one and posed the new switch back in. Not bad Part cost $11.00 7 dollars shipping so for 17 bucks it works great. nice to see what is inside the refer!

Parts Used:

David from GROVESPRING, MO
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Retainer bar was missing.

I had to cut the bar to the right length with a hacksaw. The most difficult part was getting on the plastic supports/pins on either end. I'm not sure a hacksaw is the best way to cut a retainer bar, but it worked.

Parts Used:

Neill from Albuquerque, NM
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins

2 of 5 people found this instruction helpful.

Was this instruction helpful to you?

replace missing parts

fast and easy. I got the right parts from the begining.

Parts Used:

Temperature Control Knob

Isidoro from Tiburon, CA
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

2 of 5 people found this instruction helpful.

Was this instruction helpful to you?

missing door shelf retainer

ordered new retained and fastners
cut to length per instructions
installed
repair completed
thanks for your service all parts were correct and deliver on time

wayne winkler

Parts Used:

francis from longmont, CO
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins

1 of 3 people found this instruction helpful.

Was this instruction helpful to you?

refrigerator was freezing

Removed light bulb first, removed three screws, then remove plastic covering to disconnect three wires from temperature control element then replaced plastic covering, screws and lightbulb and was done. 15 to 20 minute job.

Parts Used:

Temperature Control Knob

Paul from Sterling, IL
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

2 of 6 people found this instruction helpful.

Was this instruction helpful to you?

cut to size and installed

I simply measured for the correcy length, cut with a hacksaw, inserted the ends that attach it to the door and installed it on the door ..... simple.

Parts Used: