GSA20IEMCFBB General Electric Refrigerator - Instructions

I took the ice bucket out and looked at it carefully. The auger was breaking apart little by little. I went on-line to find what part I needed. I came to Part Select and they had a diagram telling exactly what part would solve my problem. I ordered it online and it arrived, nicely packed about four days later. I took out the old ice bucket with the broken auger and replaced it with the new one (which I washed out before installing). It was so easy and I didn't have to pay a repairman to do it. The price was reasonable, too. I have this site bookmarked in case anything else needs to be replaced. It's amazing what you can do yourself!

Watched video, however could not get outer casing off. Under the panel are three small holes, pushed up with an Allen key, used a small screwdriver to wedge out, came out easily, followed instructions from video on removing and replacing solenoid

Unfortunately, the replacement part didn't come with instructions. The repair, nevertheless, was fairly straightforward. After removing the plastic parts that guide the ice through the door (by removing a few screws that attach the parts to the inside of the door), I was able to slip my hand into the ice maker dispenser and remove the old part. The part clips on. It is a tight fit through the funnel (from the outside of the freezer), however, and requires that the gasket first be "flipped" open wherein it unfolds 180 degrees. Doing this will make it easier to clip the new gasket onto the assembly.

Removed panel from front of freezer door by pushing up on three spring loaded screws located in the opening where the ice door opens and closes. they are about 1 inch apart on the bottom of the opening. Push up to free ice maker panel. Remove three screws from solenoid, located at the top right. Remove wire, replace with new and that is it. Fixed the problem!! Our ice maker hadn't worked for months. Be careful if you remove the round ice maker door to clean. There is a spring that located on the left side of sprocket. The spring fell off and took me a while to figure where it came from. Recieved package in three days and the job took minutes. Works great! Very easy to complete.

The repaire guy came in tooke it out and told me it is goin to coast $20 for the part and $50 for the labor..... So I looked, It was soooo eeezzz ALL you have to do is get the switch out( with help of my butter knife :) it plugs in to a little outlet on the wire (on the botom side) so take out the old one and plug in the new one wich I got for $8 + $6 shipping = $15 THANK YOU PART SELECT for saving me $55 Im a 36 y/o stayathome mom and Ihave never don this before, Im very proud of my self. well... it was very easy!

Undid the three screws (one just held the light, which had to be detached but not removed from the refer), cut the lines several inches up, and removed the old reservoir. No quick connects came w/the part, and 5/16" items are not available in most stores, including Home Depot, Lowes, Ace, True Value, etc, so had to order separately on line (search 5/16" quick connect) (another $12 with S&H). Don't use a pinching type tool to cut the lines - not a smooth cut. I used a miniature pipe cutter I happened to have because I am a hobbyist. Cut the lines on the new reservoir at same place as old one, pushed the quick connects on, pushed the QCs on the lines sticking out of the refer, replaced screws, and was done. Quick connects should be included with this part.

Removed the plastic frame by pushing to the inside (all 4 sides), removed touch pad by sliding it to my right and disconnected the wires. Removed the four screws that hold the dispensing unit and replaced broken parts. Please note that I also replaced the funnel. Total cost of repair for DIY $30.00, savings by avoiding repair man, priceless.

Removed the ice bucket and put the new ice bucket in placed
.
work like a top.

Removed tray, threw out ice , removed 3 screws used 2 screw drivers to seperate part & re installed

Remove rear plate. Remove fan bracket. Replace fan gaskets, blade and motor. Replace bracket. Replace rear plate. Very simple. Fixed the problem.

Your instructions were "spot on"! Pried out broken switch with screwdriver-reinstalled new switch. Very easy! Ordered on line on a Wednesday new part arrived on following Saturday-Great service and will definately use again. Highly recommend PartSelect!

Took out the old, put in the new. Problem solved.

pulled out broken bucket and auger assy. and slid in the replacement. works great so far. The easiest part was ordering the part and it didn't take very long at all to get it. Customer Service was very good at getting the job done. Thanks

Replace

Replaced defrost thermostat along with temp sensor watched the video on this page simple fix