GLD7768V00SS General Electric Dishwasher - Instructions

followed the video step by step which was very well expalined and was able to complete the install

I watched the video that came with email on part. Gave instructions on how to. Thank you !

Unscrew the old one and screw in the new one.

Attached the drain hose to the dishwasher pump and to the sink pipes and I was done.

It couldn't have been easier. I installed the new wheels in seconds and the rack glides as perfectly as the day it was installed 11 years ago! Perfection! Your stellar website made it so easy to find the correct parts. BRAVO!!!!! I laughed! I cried! I am so ECSTATIC!!!!!

The kit came with the anchors and the riollers for the bottom shelf. They clipped right on! Dishwasher cleans great now!

Pulled off old rollers and snapped on new ones. Never easier!

delivery of part was very quick, and my husband was able to remove the old part and install the new in about 10 minutes. No service call; no new rack; just a washer that is easy to use again.

Watched online video, repaired myself in under 10 minutes.
Easy fix with video instructions

Removed the unit from under counter and placed it with the door side down. Removed clamps/bands from the outlets on the sump and removed screws that attached sump to dishwasher tub. Reversed the process with the new sump and positioned the dishwasher unt=der the cabinet. Next step was to remove the arm and cover parts to the sump, then removed the old upper neck portion that stuck to a strainer. Then aligned the strainer to connect to the small neck of the sump and replaced items in the order from which they were removed.

Ordered most likely part...water inlet valve.

1. Turn off water supply.
2. Remove the metal toe kick plate/insulation at the bottom of the
dishwasher.
3. Remove hose to supply valve.
4. Take electrical plug off old valve.
5. Remove float valve because it was mounted it right in the way of
the 2 screws on the inlet valve bracket.
6. Remove those 2 screws now you can get to them, and move the
inlet valve to one side so you can get to the hose clamp for the
rubber hose out of the valve going to the dishwasher.
7, Take the old valve and bracket out, mount new valve on the
bracket, crawl back down on the floor, reinstall rubber hose and
bracket, and float valve and finally inlet hose.
8. Turn water on. Check hose connections for leaks. Yep, outlet
hose didn't clamp enough now, allowing a drip.
9. Repeat the whole process AGAIN. Replace little clamp
with a REAL hose clamp, reinstall the thing again. No leak this
time.
10. Test run dishwasher thru a cycle. Check again for leaks at hose
connections. OK ? Reinstall insulation pieces and toe kick
plate.

Ordered a new tub gasket and, although the gasket went on backorder for two weeks, the repair itself was extremely easy requiring no tools at all!

Put new basket in, threw old one away

First removed the eight philips head screws that hold the outside bottom door cover, to get access to the module. Then removed the two wires and the ten screws holding the module in place. Put the new module back in, reconnected the wires, and re-tighten everything. Did not have to use the bracket and cap.

The installation video that is on the website with the part is very helpful & easy to follow. The wires that attach to the heating element & the nuts that hold it in place are actually located a few inches off the ground so I didn't need to tip the machine over to pull them out & unscrew the nuts. All I had to do was unscrew the screws that hold the dishwasher in place under the counter next to the sink, pull it out & was able to reach the wires underneath it.
The actual repair took me less than 30 minutes, I marked it as 30-60 because during the somehow the water line going to the dishwasher had come loose from under the sink (not at the dishwasher) & because of this I had to stop midway to deal with some loose water & tighten things back up. I would recommend following the video, there really isn't much more to add that would be helpful.