GI6FARXXF02 Whirlpool Refrigerator - Instructions

Took out the old and installed the new.. The fit was perfect.

The troubleshooting time takes about 20 to 30 minutes. After checking out the solenoid (valve water), the water line, and the electronic board (emitter/receiver) are working fine. The only thing left is the ice module. I called Partselect and talked to a sale rep to make sure I get the right part, and the lady was so helpful by sendind the picture of the part so I can review before ordering it. I received the part in 3 days ( normal shipping) and did the folowings:
1) Unplugged the power cord from refrigerator.
2) Removed the ice module by removed a 1/4" screw from under the right side of the icemaker that retains the icemaker and a “U” plastic clamp and then pull out the whole unit it from the track.
3) Unplugged the cable connected to the ice maker.
4) Using the phillips screw driver to remove the 3 screws. Carefully pulled out the ice module and installed the new ice module.
5) Put the ice maker back to the freezer, plug the cable back to the ice maker and put the clamp and tighten the nut.
6) Plugged the power cable back to the wall.

The first ice I got in an hour and a full bucket of ice in less than 24 hours. I spent less than $80 for the whole thing. Thank you so much Partselect for the great service and the stories posted, it really helped me to get it done.

Replaced filter and the water started to flow like the Nile River and the ice maker came back to life.

Unscrew filter. Screw on filter bypass

Remove rail and removed broken black plastic spring mechanism with new one and then replace rail.

Since it wasn't possible to squeeze the seal in between the door groove and the bar which closes the gap between the two doors, I cut the seal side in half and snaked it in from the top and the bottom. Since the cut is behind the bar when the door is closed there is no compromise in getting a good seal around the door. Note there was no apparent way to easily remove this bar.

Very easy. Just get hold of the gasket with your strong fingers and pull it out of the groove it is in. Clean the groove, I used Windex and paper towels. On the new gasket there are 2 wide areas on the vertical part. these must be facing toward you and on the handle side of the door. start at the tor center of the door and work the gasket in with your fingers outward to the corners then work on the bottom of the gasket in the same manner, then start on the vertical gaskets. when you think every thing is aligned take your thumbs and press very hard all around. You may have to repeat.

Layer it out for 24 hrs used hairdryer on med for the wrenkles.

Pop off vent cover remove 2 screws removed cover housing and foam. Removed damper by unclipping tabs on left and right side of control lift up and out. Unplugged power wires reinstalled in reverse order.

Easy fix, it's right in the back of the fridge under a cover that just clips in, a piece of foam, and two screws. The hardest part is getting the clips free without breaking them. After replacement it's silent instead of making a grinding noise regularly.

Removed old ice maker by removing 3 screws, unplugged wiring harness. Replaced with new ice maker, placed three screws back to secure the ice maker, plugged wire harness back, and product is working well at this time.

The old cover was off and I just slid the replacement part that I got from you'll, it just slid in place and snapped close. Perfect fit. Thanks guys

Remove back cover
Remove drip thing from top to tray in the back
Remove fan motor assembly. This is squirrely. Top bends towards you, bottom pushes in to the unit. Not fun.
CAREFULLY remove copper tube that rests on drip tray
Remove tray - there are clips in the front that get released by screwdriver
Clean up
Replace new tray
Replace copper tube
Play with fan motor assembly till it fits. It doesn't look like it's gonna work until it does. See youtube videos on this.
Replace drip thing from top to tray - I forgot this one the first time.
Replace cover.

This is a simple, but squirrely, repair. Right on the border of easy (because so few tools and steps) and A Bit Difficult because of the patience required.

Watched video. Unplugged refrigerator and popped out switch. In plugged connector and pushed switch in place. Plugged in refrigerator and the light worked

I removed and disassembled the broken frame. I cut a six inch piece of coat hanger and folded in half and crimped together. Then I took pliers and made a hook that I hooked into the metal strip in the back of the refrigerator that holds the upper shelves. After replacing the frame, center rail and glass I bent the wire up under the back of the frame to provide a support. The back of the frame is weak and has no center support.