GFDN240GL0WW General Electric Dryer - Instructions

Unscrew the top panel parts three screws. Then another three or six screws to get to the dryer front which needs only to lift straight up about two inches. Pull back slightly and replace the teflon slides. To replace the slides they lay on a tiny plastic pin and slightly bend into the slot to hold them in place. Reseat the dryer drum. Reverse the process to make it like new. From the time you start hearing the dryer squeak, BE CERTAIN to replace these within a week or two (depending on usage.)Otherwise, you may wear out the housing where the teflon would rest. If that happens, you will be out more money to replace the housing and a lot more time to install. Been there and done that. Trust me.

I used these two videos to help me clean the inside of the machine, then change the drive belt.

Followed the online demonstration on the website when i ordered the part. The video was outstanding and easy to follow. I now have the confidence to make other minor appliance repairs.

Dryer would turn on when you pushed the "on" button, but as soon as you let go, it would turn off. Found the plastic door switch cracked (from slamming door closed). Unplugged the dryer. Unscrewed the two screws inside the top of the door to unfasten the top panel. Took the top panel off. Then unscrewed the two screws on the side to unlatch the front panel. Used plyers to take the 3 wires off the switch and slid the switch through the front of the door. Juat remember where the wires go. Then inserted new switch and connected the wires. Vacuumed out the dryer and reassembled. It took about 20 minutes and was easy! If I can do it, you can!!!

remove front and top cannover's from dryer.remove plastic inside bearing housing and plastic bearing slides replace worn out bearing slides with new ones. needed 4 bearings direction suggested only two....

Faulty Door switch. Dryer would heat up so I knew it wasn't thermostat or element related.

After some research on the internet, I deduced the squeaking sound in our dryer was due to defective drum glides. I ordered a set of four of the white type, knowing only our model requires four glides, but not knowing there are two types for two locations. After disassembling the dryer I realized I needed more parts - two green slides and a new top bearing assembly. The dryer drum had eaten thru glides and into the plastic assembly. That was the reason for the squeaking noise - metal sliding against hard plastic. I ordered the additional parts directly from the manufacturer to ensure I got it right. After all the parts arrived, the repair was easy and took less than 30 minutes. I actually had my 17 year-old daughter do the work to teach her some skills. I just instructed her and stepped in on assembling the top that was just a bit tricky to put back on. Problem fixed.

very easy

Unscrewed the top lid screws located in door opening.Removed lid.Unscrewed the front cover screws located at top corners of cover, underneath where the top lid was.Pulled out drum,removing belt at same time.Removed the rear bearing unit,installed new one.Really easy.Took front bearing off front cover,it just snaps on.Installed new bearing,with 4 new slides.Reassembled machine,replacing old belt at the same time.Done.It really is that easy.Spent more time cleaning lint out of dryer interior than actual mechanical work,I think.

Replaced drum bearing part and white slides.The problem was that it was not the drum slide support. It appears to be the the drum rear bearing of whch I am now ordering. The bearing replacement is a little more difficult, but I have taken this on as a challenge

1. turn off gas.2. disconnect electric.3.Remove 3/8 gas line from rear of burner. 4.disconnect two electric connectors from gas valve assembly. 5.disconnect electric line from igniter. 6.remove two mounting sheet metal screws from front of gas valve assembly(5/16 socket). There also may be a screw holding assembly to the bottom plate.7. remove entire assembly from dryer by pulling out to the front. 8.remove igniter assembly and replace on new burner. 9. two sheet metal screws 1/4 inch hold burner assembly to gas valve assembly.10.Install in reverse order . it may take a few seconds for the gas to get down to the burner. don't forget to change over the air mix valve to the same place.

My son ordered the part, but gave up installing it. We called in a professional appliance repairman because the dryer had to be partially dismantled to remove the drum and a belt so three sets of holes could be aligned to secure the replacement diffuser. My daughter had to lend a hand to hold one piece in place while the repairman threaded the screws because the drum was too deep for him to be able to reach both front and back pieces. Definitely not a one-person job for this particular model.

This is the 2nd time we had to replace the slides. Not a big deal. Removed the top & front of the dyer and replaced the new slides. It's also a good time to vacuum out the inside while you have it apart. Be advised.... Get your tools ready. You'll be receiving your parts quickly. Couldn't believe how fast they arrived!

Thanks to your great DYI video I completed the repair in less than 45 minutes very easy.

Great service. I got the part in 3 days and having the youtube video was fantastic. I also was able to find other videos also so doing these tasks yourself nowadays is much easier. I was a bit nervous but it turned out to be easy.