GFDN240GL0WW General Electric Dryer - Instructions

it was easy, it clip right on.needed to give it a little tap to get it in .

I followed the great tips from the other repairs and that part was easy. Turned out not to be the exact problem. The problem was the rear bearing shaft which in another 20 min I had the drum out and repaired. Now the dryer is like new and will hopefully last another 5 yrs.
Thanks Parts Select for your help!

Took off the top and front of the dryer---really easy, just two screws for each. Put new drum slides (4) on the front/sides of the drum. Then things got a little bit more difficult. Removed the drum entirely, vaccuumed everything out and had to replace the rear bearings. My husband did this part so I can't tell you exactly how he did it. Not too difficult though. The written directions from here were hard to read---need to make a new copy from the original as it's so copied that it's all smudged. Anyway, once we got the new bearings on, we put everything back together. Dryer works like a charm, at a fraction of the cost it would have been to get someone out to do it. Thanks a bunch for the fast service!

Removed the 3 star screws, putting in a piece if wire as I removed them. Wire was not stiff enough and let the drum slip thus binding making it hard to remove. Started over. Finally called a friend for help. I bought 3 tension pins the same size as the screws. When removing the diffuser screws, insert a tension pin in the hole as you remove each of the screws. The tension pins are hard metal and do not have a head. The diffuser will slip over them. After the diffuser was in place, we turned on the dryer to make sure it was running ok. I noticed what looked like lint toward the front. It was part of the felt gasket on the front of the drum and front of the dryer. We removed the screws on the dryer front and pulled it forward. The felt was rethreaded into its slot, put the front back in place,and replaced the screws that hold everything in place. If you turn the part of the dryer that spins by hand, make sure you are turning it in the correct direction. Turning it the wrong way is probably what caused the felt gasket to come loose causing more work.

Removed top cover by removing 2 screws in front door opening. Then removed front door removing 2 screws, one on each inner side of the front door.
Removed 2 screws on side doors located about 9 inches from bottom of dryer to permit taking off drum. Slip off belt and remove drum.
Thinking I had a bad bearing, I decided to turn the dryer on and found out I had a bad motor-still functional but noisy. I had difficulty installing the new belt since there was not access panel (which was mentioned in the service manual), so I decided to take off the left side panel-about 8 screws. With the left side panel off, it was a lot easier to install a new belt and install the new front bearings. I actually did not fix the noise, since I need to replace the motor ($$$). When it goes really bad, I can order it then, and it should not take me long to replace it.

I ordered and replaced the front and rear bearings, including the slides that go on the front bearing. Most of this was un-necessary; replacing the slides would have been sufficient, and much easier to do. Two of the old slides were worn completely away.

no problem open top remove front install new belt

Removed the top of the dryer 2 screws. procedure
open dryer door. At the top of the dryer door their is
two screws left to right, Remove them and lift top
off. Inside where the top was is two screws left to
right. Remove the two screws and take the front
panel off. Carefull not to pull wireing loose. Lean door against something so you don't have to disasemble wireing. Pull broken belt out and install new belt around tumbler and up and over
tension pulley and pull down and slip over the motor pulley. Your'e done. Reassemble front then
top. My dryer ran just fine after these steps. The question and answers helped me do this.

This is a space saver one piece unit with dryer on top. I first removed ten screws that hold the top on, I then removed four more screws that hold the front service cover on and two last screws that hold the rear service cover on. Now I seperated the front cover of the dryer from the dryer tumbler tub and slipped the new belt around the tub, then at the rear service cover I feed the belt through the tensioner and back onto the motor pully. Now just put the covers back in reverse order of removal and all done! "Piece of cake"
Ron

Followed the video which made it real easy.

Removing the top and then the front of the dryer went fairly easily after finding the screws. The drum came out with just a little coaxing, does not gets screwed in place. To me the trickiest maneuver was getting my hand under the drum to place the belt over motor pulley and around the tensioner pulley. You must look up an image of the belt routing. It took me forever to figure that out. If not for that, this in a half hr fix. Ps don't forget to unplug the dryer.

Followed the Part Select video instructions which made the repair really easy!! Thanks for a job well done! ALSO.. the drum wobble was not caused by worn slides and felt. There are three screws holding the drum axle flange. Two of them fell out leaving the drum to flop about as it rotated. So we scavenged some screws from elsewhere on the dryer and problem solved. Once again.. thanks to Part Select for great instructional videos and great customer service ordering parts.

I followed the provided video precisely. Made the job quite easy. My only problem is I'm 6'2", 275 lbs. with bad knees. Can't go at it exactly as shown in the video because I can't squat down in front of the dryer without pain. Called in a neighbor of smaller stature for him to come from one side, and me from the other. Worked flawlessly. Video is excellent. I do recommend wearing gloves and/or long sleeve shirt. I cut up my arms a bit, but that could have been easily avoided.

Watch the video on how to replace the belt on PartSelct site belt installation page.

Easier than I thought it would be. I was hoping it was the front bearing because replacing the rear bearing looked pretty gnarly. Unplugged the dryer from the outlet. Removed two screws inside the door frame. Lifted the top off. Unscrewed the two screws holding the front on. Lifted the front panel off, careful of the wires going to the door. Popped out the old front bearing by releasing the two clips at the top. The old bearing was pretty trashed. The two grey/green slides were in tatters and one of the white ones was missing. Not too much lint inside the dryer, but the lint trap was pretty clogged. Cleaned the insides out with the shop-vac. Inserted the new slides into the new bearing an snapped it back into place, careful to make sure the light went in the hole. The felt gasket at the botton was in good shape so did not replace it. Replaced the panels screwed them back to together and it fired up smooth and quiet.