FGID2466QF6A Frigidaire Dishwasher - Instructions

Removed screws for door panel, then literally 2 screws to change out the latch!!

Removed all sealer and install new one as instructed.

Removed 6 screws from door front panel. Removed two wiring connectors and screws fromdoor latch Replaced and all is great

For some strange reason my new dishwasher was installed without a door gasket, which caused a very small water leak. The gasket I purchased was installed in less than 5 minutes and corrected the problem immediately - a very easy task and I am no handyman!

After getting a totally incorrect length of hose from partselect.com . Went to local hardware store and bought hose for $3.00 vs $20.99 + $10 shipping!
Partselect sent replacement hose of 24 1/4” vs the original hose of 27”. Good luck getting any response from them once they have your money!

Replace the latch. Got to cut off old latch, trim wires, install latch, and put on the dishwasher door cover back on with screws

The replacement hose was not as long and the original and therefore did not fit into the track made for the original one. Though it was long enough to work, an additional 4 inches would have been an exact fit.
As a result, the replacement had to be duct taped to the side of the dishwasher to hold it in place. Otherwise, the new hose was of better quality that the flimsy original. All in all, I could have picked up 3 feet of rubber hose from an auto parts or hardware store cheaper and done the job just as well, if not better.

Disconnected power, water, and drain tube from dishwasher. Pulled dishwasher out and laid it on right side. It was not necessary to remove the pump motor. When disconnecting the water line, it is better to remove 3/8 line from the appliance adapter rather that the appliance adapter from the dishwasher as the nylon connection tends to strip.

If you are getting intermittent leaks especially when you put a pot lid up front, it’s probably just the door gasket. And this was the easiest project I’ve tackled as a homeowner since buying the place 20 years ago. I read the other stories and I think the suggestion I choose to follow is not the best thing to do. So, read passed where I cut the gasket. I used needle nose pliers to grab the bottom edge of the old gasket which then pulled out by hand with almost no effort. I used the old gasket to measure the new gasket as recommended in one of the other stories, and cut it. DON"T DO THIS. The gasket is very soft foam rubber. As you push it in (I just used my fingers), it will get longer as you push it in. I put it in the first time (took about a minute if that long) and even though I cut it to the same length as the old one, it was too long. Obviously I figured I did something wrong. So, I took it out and measured it again. Nope, same-same. So, I put in a second time, careful not to stretch it, and this time it was now too short. So, I recommend that you just establish the bottom edge 90 degree angle seat and try not to stretch it as you work your way around the seam. It should fit just find, maybe with a little adjustment back or forth, but without cutting it at all. By the way, the half inch I cut off at the recommendation of one of the other reviews did not ruin it. It works just fine. So you can cut it if you want I suppose. But that half inch I cut off was what I was short when I was carful not to stretch it.

First I removed the two screws that hold the dishwasher in place, I pulled out the dishwasher and on the bottom right located the leak. The two brass nuts that hold the heating element in place. The wires had been rusted to the element so I cut the wires (and later spliced them back together) and unscrewed the brass nuts. I ordered the part after finding them very easily on partselect.com and 2 days later screwed them back on to the dishwasher. Spliced the wires back together and put the dishwasher back in place.

Easy Fix.

I left the unit in place. I removed the bottom cover, unplugged power from GFI receptacle and closed water supply valve. I unplugged the electrical connection. I put a dishtowel under water inlet valve and removed water supply. I removed two screws from inlet valve bracket that allowed me to rotate the valve and used pliers to remove water hose clamp and hose. I installed the new valve in reverse order. I checked for leaks; found none. Life is good again!

Easy

VERY simple---unscrewed three screws on the broken part (the little nubs that held on the bottom spinner were broken off), screwed the new one back in, re-attached the spinner.

I was VERY pleased with the customer service and quick shipping (ordered on Sunday night, the part was delivered Wednesday morning). I would definitely recommend this site to anyone, and would use it again. Five Stars!!!!

Unscrewed the housing for the old piece and screwed on the new part. No tools needed. Easy to use website, fast delivery. Very easy.

It only took about 20 minutes to replace. Thanks for the video.