This grey OEM dishwasher tub gasket is a 73" grey rubber part that creates a seal around the dishwasher to prevent any water leakage during a cycle. If it's damaged or broken, you'll start seeing wate...
The upper spray arm helps distribute water from the top of the dishwasher tub.This spray arm is a genuine OEM replacement part for your dishwasher. This spray arm is for the upper part of your dishwas...
The single rack roller kit comes with one axle/clip and one wheel/roller. The rack wheel is designed to allow the rack of your dishwasher to roll in and out. If the rack will not complete this task, o...
The spray arm rotates and sprays water to clean the dishes inside the dishwasher tub.
This part works with the following brands: Frigidaire, White Westinghouse, Kelvinator, Gibson, Kenmore, Sears, ...
This door seal is for dishwashers.
Door seal seals the gap between the opening to the dishwasher tub and the outer edge of the door.
After installing the door seal, shut the dishwasher door and ...
The drain pump ejects the water from the dishwasher.
$137.48
In Stock
Questions And Answers for FGID2466QF6A
Ask our experts a question about this model and we'll get back to you as soon as possible!
7 questions answered by our experts.
< Prev
1
2
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Roselle
July 16, 2021
The spinning section of the center spray arm has detached. Can it be reattached or does the entire spray arm need to be replaced?
For model number FGID2466QF6A
Hi Roselle,
Thank you for your question. If the spinning portion of the center spray arm has detached, then you will need to replace the entire center spray arm. The part number listed under your model number for the center spray arm is PS11770527. If you would like to place an order for it, you may order it either online or by calling our customer service line and anyone will be happy to assist you. We hope this helps! If you have any questions, please let us know.
when I open door and press start the unit says to close door. When I close door the display goes back to timer but does not start unit. Is the door latch bad?
For model number FGID2466QF6A
Hello Kevin, thank you for your inquiry. Based on the description that you have provided, we would recommend checking the door latch, part number PS16218716, to fix the issue. This door latch with the switches is a simple on/off mechanism that prohibits the dishwasher from operating when the door is open. We hope this sorts out your problem!
I am concerned it will start leaking from the door bottom.
For model number FGID2466QF6A
Hello Katie, thank you for reaching out to PartSelect. Based on the description that you have provided, we would recommend checking the door bottom seal, part number PS11703834, to fix the issue. We hope this solves your problem!
The panel lights won't come on. The unit will run eventually by pressing the start button but none of the other panel lights come on with exception of the delay button.
For model number FGID2466QF6A
Hello Randy, thank you for contacting us. It appears that your dishwasher may have a damaged control board, part number PS12365809. Good luck with the repair!
I tried to clean the lower arm because it wasn’t cleaning well and snapped it in 2. Is there a way to replace this? I don’t see the part
For model number FGID2466QF6A
Hello Elisia, thank you for your question. We have researched the model you have provided, and we would suggest the Lower Spray Arm, part number PS11770610. We hope this helps!
Repair was simple. I unscrewed the old grommet which held the old spray arm and screwed-on the new one. About 30 seconds was required. Other people having this problem should note that the spray-arm is made of three pieces which are inseparable when the arm is new. The arm is sold in this form. However, when your machine is having the problem that the arm falls off, the three pieces become separate. When you want to replace the spray arm, only one new part needs to be ordered because this part encompases all three components.
I removed old tub gasket, which the door presses against to make a seal, and put the new one in. Flat tip screwdriver was used to gently press gasket in.